Belmont Medical Technologies RAPID INFUSER RI-2 Скачать руководство пользователя страница 1

Страница: 1 / 9

IV POLE

RI-2

UNIT

SUPPORT

CLAMP

PLASTIC

WASHER

RESERVOIR SUPPORT

Step-By-Step Quick Set-Up

SETUP:

•

Inspect the system



Power cord: 14/3 SJT cable with Hospital plug

(

USE ONLY SUPPLIED POWER CORD

)



IV pole: 5 wheel IV pole (max. diameter 1 1/4")



Pole mount support assembly (Support Clamp & Plastic washer)



Reservoir support



Disposable set



3L Reservoir and reservoir holder, if needed

MOUNT ON THE IV POLE:

30 in (76 cm)

Pole Clamp

Release Handle

SETUP / MOUNT ON IV POLE

•

Mount The Belmont

Rapid Infuser

RI-2

app. 30” from the ground

•

Tighten the “Pole Clamp Release Handle”

onto the IV pole

•

Install the Pole Mount Support Assembly

(support clamp and plastic washer) under

the

RI-2

•

Clamp the Reservoir Support above the

RI-2

Содержание RAPID INFUSER RI-2










Результаты поиска

Содержание RAPID INFUSER RI-2

Отзывы:

Похожие инструкции для RAPID INFUSER RI-2

Бренды по названию

Популярные бренды

Belmont Medical Technologies RAPID INFUSER RI-2, Быстрая настройка

Результаты поиска

Содержание RAPID INFUSER RI-2

Отзывы:

Похожие инструкции для RAPID INFUSER RI-2

Бренды по названию

Популярные бренды