Fountain Tower
Plumbers
Tape
Dancing Water
Attachments
Battery
Compartment
& Water Pump
CONTENTS:
Assembly
Water
Pump
Battery
Compartment
(4D Cell Batteries
Not Included)
Dancing Water
Attachments
Water Pump Tube
Vent Hole
Vent Hole
Battery Cover
Max Water Level
(Upper
Decorative
Ring)
Battery
Cover
Retaining
Nut
Bowl
(Not Included)
Recommended minimum bowl size is approximately 12 inches
Min Water Level
(Lower
Decorative
Ring)
Min Water Level
(Lower
Decorative
Ring)
Diagram 1a:
O W N E R S M A N U A L
Please note, images of parts are not to scale with one another.
INSTALLING BATTERIES:
1. Unscrew (counter clockwise) the
Battery Cover Retaining Nut and open cover
(Figure 1a, 1b).
2. Position the Battery Compartment with locating
dowel on top. (See Arrow Figure 1c &1d).
3. Insert 2 batteries (Figure 2a) with the (+) side
facing up in Battery Compartment (upper left and
lower right) and 2 batteries with the (-) facing up in
Battery Compartment (upper right & lower left).
4. Reinstall the Battery Cover by aligning the
locating dowel in the Battery Compartment and
Battery Cover. Set the Battery Cover down onto the
Battery Compartment ensuring the dowel sets into
the alignment hole. Tighten the Battery Cover
retaining nut by turning clockwise until you hear a
clicking sound. This indicates the Battery Cover is
sufficiently tight. (Figure 3a & 3b).
1. Take the Battery Compartment and Water Pump & connect one side of the Water Tube to the Water Pump and the other end to the bottom side of the Battery Compartment (A & B of Figure 4).
2. Find a suitable bowl, place it on a flat level surface, place the Fountain without the Battery Compartment and Water
Pump, into the center of the bowl.
3. Lower the Battery Compartment and Water Pump into the Fountain and make sure it sits level on Fountain (Figure 5).
3. Fill bowl with water, water level should be between the upper and lower Decorative Rings on the outside of the
Fountain. This will ensure water covers the Water Pump (Diagram 1a).
OPERATING YOUR CREATE-A-FOUNTAIN:
Turn Fountain on and set timer: When the Fountain is off, set the run time for 1 to 4 hours by slowly pressing the button 1 to 4 times
(Figure 7a & 7b). 3 seconds after pressing the button, the LED light will repeatedly flash the number of times the button was pressed (Figure 7a).
This indicates the number of hours the Fountain will run every day. The Fountain will turn on at the same time, for the selected number of hours, daily thereafter.
Stop Fountain for one day: To stop the Fountain manually for one day, hold the button for over 2 seconds (Figure 7a & 7b). The Fountain will turn off for one day, but will still turn on at the
same time, for the same number of hours selected, daily thereafter.
Reset/Change the timer: To change the run time, stop the Fountain if its running by holding the button for over 2 seconds (Figure 7a & 7b). The Fountain will stop. Once the Fountain
stops, you can press the button again to set the duration. Refer to Turn Fountain on and set timer.
Fully shut off and clear timer: To fully turn off the Fountain so that it will not turn on automatically the next day, press and hold the button for over 2 seconds to turn it off (Figure 7a & 7b).
When the Fountain is NOT operating, simply press hold the button again for over 2 seconds, the LED light will come on for 3 seconds steady to confirm daily program is off.
DANCING WATER ATTACHMENTS: (OPTIONAL):
To prevent overspray there are 3 Dancing Water Attachments designed for large bowls & 1 designed for small bowls please use accordingly.
When Fountain is not running, select one of the Dancing Water Attachments and attach to the outlet in the middle of the Fountain Tower
(Figure 8a, 8b & 8c)
.
*PLEASE READ THESE INSTRUCTIONS COMPLETELY BEFORE ASSEMBLING YOUR NEW FOUNTAIN
Figure 6
Figure 5
Figure 1b
Figure 1a
Figure 3b
Figure 1c
Figure 1d
Figure 4
Figure 3a
Figure 2b
STEP
2.
STEP
3.
STEP
Figure 2a
CHANGING BATTERIES:
1. Remove any Dancing Water Attachment, lift Battery Compartment
and Water Pump out of the Fountain (Figure 6). Ensure Battery
Compartment and Water Pump are completely dry before
opening Battery Compartment. It is important that no water
enters the Battery Compartment.
2. Reinstall batteries and reassemble.
3. Set the Battery Compartment and Water Pump back into the
Fountain (Figure 5).
Figure 7b
Figure 7a
LED
Light
LED
Light
Button
Button
Need Help?
Call us for assistance at: 1+ (619) 449-2392
or you can email us at: customercare@
belmont.garden
Our Customer Care Department is available:
Monday - Friday 8:30am to 4:00pm PST 11:30am - 7:00pm EST
Locating
Dowel
Locating
Dowel
Locating
Dowel/
Alignment
Hole
Battery Cover
Retaining Nut
Battery Cover
Retaining Nut
Battery Cover
Retaining Nut
Battery Cover
Retaining Nut
Dancing Water Attachments
Please use accordingly
to prevent overspray
Large Bowls Small Bowls
Figure 8a
Figure 8b
Figure 8c
17 in (43.18cm)
diameter or
larger bowls
11.5 in (29.21cm)
to 17 in (43.18cm)
diameter bowls
Create-A-Fountain
TM
Locating
Dowel/
Alignment
Hole
