Bell System bellagio Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 52

background image

bellagio Digital Entry System

PD

–

281 Issue 1

Installation and Operating Manual

Page 17 of 52

Power Supply Requirements

The system is powered by 12V power supplies only: -

Model PS4 12V, 4A.

Model 840

12V, 4A battery backup supply.

Note 1. The PS4 power supply has been specifically designed to operate with the
requirements of the system. Bell System is unable to guarantee functionality or provide
support for systems which use third party power supplies.

Cable Specification

All system wiring must be carried out using

Cat5

signal cable and where necessary 1mm²

(or greater) power cable as tabulated below. Cat5 cable has a known performance for the
transmission of data signals, whilst telephone or alarm cables are not suitable.

Bell System will be unable to offer any warranty or support for systems installed
using incorrect cables.

Cat5 Cable Specification

Cat5 is our short reference for EIA standard UTP Category 5 Unshielded Twisted Pair data
cable. This is a standard solid core twisted pair cable having 4 pairs (8-cores) and no

shield. The cores are in pairs where Blue and ‘Blue with a White stripe’ are twisted

together as the first pair. The other three pairs are similar with main colours Orange,
Green and Brown.



Also available and acceptable are:

UTP Category 5e (Cat5e)

UTP Category 6 (CAT6)

UTP Category 6e (CAT6e)

The exact cable can be chosen from the above on cost and availability grounds.



STP (Shielded Twisted Pair) cables are

not

recommended.



UTP “patch cables” are

not

recommended.

NOTE: Cat5 cable is easily identifiable as the specification is printed on the sheath

«
...
15
16
17
18
19
...
»

Содержание bellagio





















































Отзывы:

Нет отзывов

Похожие инструкции для bellagio

Бренд: JBL Страницы: 2

Бренд: abc Страницы: 8

Бренд: Radio Shack Страницы: 1

instant theatre KIT100

Бренд: KEF Страницы: 48

SecurAccess PMR

Бренд: Depaepe Telecom Страницы: 51

Бренд: Eaton Страницы: 7

Бренд: Ibiza sound Страницы: 40

Бренд: Fender Страницы: 6

System One M200

Бренд: iCentral Страницы: 44

Бренд: W. A. Production Страницы: 5

iNELS Air AirIM-100S

Бренд: Elko Страницы: 8

Бренд: ICP DAS USA Страницы: 21

Бренд: Omron Страницы: 114

INSTYLE ECOUSTIC TANGO

Бренд: unika vaev Страницы: 2

Бренд: ICP DAS USA Страницы: 8

Бренд: JAMO Страницы: 17

Бренд: Argus Страницы: 38

Бренд: Johnson Controls Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды