manualshive.com logo in svg

BelAir Networks BelAir 100SN, Руководство пользователя

BelAir Networks BelAir 100SN - высококачественный сетевой оборудование для установки внутри помещений. Скачайте бесплатно Руководство пользователя для настройки и использования продукта с manualshive.com. Необходимая информация для правильной настройки и оптимальной работы сети. Идеальный выбор для дома или офиса.

Поделиться
Скачать
background image

BelAir100SN User Guide

Using Layer 2 Tunnels

May 31, 2010

Confidential

Page 156 of 212

Document Number BDTM11001-A01 Released

If you specify a DSCP value, then it appears in the DSCP/TOS bits of any L2TP 
or PPP control packets. 

Configuring Layer 2 

Extended Tunnels

/protocol/te-<eng>/set tunnel-x <index (1-5)> 
                       source <if-VLAN> [backup-source <if_VLAN>]
                      lns <ip_addr> [backup-lns <ip_addr>]
                      name <host name> [backup-name <host name>]
                      [switch {non-revertive | revertive}]
/protocol/te-<eng>/delete tunnel <index>

The 

set tunnel-x

 command allows you to configure an extended tunnel that has 

two VLAN interfaces to provide redundancy in case one VLAN interface 
becomes unreachable.

First you must configure the tunnel engine to be in extended mode. See 

“Setting Tunnel Engine Parameters” on page 154

. Then, you configure the 

extended tunnel with the 

set tunnel-x

 command. 

The <index> parameter is used for easy reference when using other 
commands. It can be displayed with the 

/protocol/te-<eng>/show config

 

command. 

The 

source

 and 

backup-source

 parameters specify the primary and backup 

VLAN interfaces. The 

lns

 and 

backup-lns

 parameters specify the IP addresses of 

the LNS for each of the VLAN interfaces. The 

name

 and 

backup-name

 

parameters specify the host names for each of the VLAN interfaces. 

The <host name> parameter can be any series of 18 alphanumeric ASCII 
characters. It is analogous to the <stn_name> parameter when configuring a 
simple tunnel. See 

“Configuring Layer 2 Tunnels” on page 153

. 

The 

switch

 parameter controls whether the use of a backup VLAN is revertive 

or not. Once the BelAir unit starts to use a tunnel through a backup VLAN:

• If 

switch

 is set to 

non-revertive

, then the BelAir unit uses the tunnel through 

the backup VLAN until it fails. Only then does the BelAir unit switches back 
to the tunnel using the main VLAN. This is the default setting.

• If 

switch

 is set to 

revertive

, then the BelAir unit uses the tunnel through the 

backup VLAN only while the main tunnel is unavailable. The BelAir unit 
switches back to the tunnel using the main VLAN as soon as it becomes 
available again.

The 

delete tunnel

 command removes the specified tunnel. After using this 

command, user data mapped to this tunnel is dropped instead of forwarded. 

Содержание BelAir 100SN





















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BelAir 100SN

IDENTEC SOLUTIONS IDS1000 Hardware User Manual preview
IDS1000
Бренд: IDENTEC SOLUTIONS Страницы: 17
D-Link DIR-868L Technical Support Setup Procedure preview
DIR-868L
Бренд: D-Link Страницы: 3
D-Link AC1200 Quick Manual preview
AC1200
Бренд: D-Link Страницы: 2
D-Link Rangebooster N 650 Access Point DAP-1353 User Manual preview
Rangebooster N 650 Access Point DAP-1353
Бренд: D-Link Страницы: 67
D-Link DWL-1000AP Quick Install Manual preview
DWL-1000AP
Бренд: D-Link Страницы: 8
D-Link COVR-2202 Simple Setup Manual preview
COVR-2202
Бренд: D-Link Страницы: 2
D-Link DAP-1155 Quick Install Manual preview
DAP-1155
Бренд: D-Link Страницы: 3
D-Link Air Premier DAP-2695 Command Line Interface Reference Manual preview
Air Premier DAP-2695
Бренд: D-Link Страницы: 39
D-Link AirPlus DI-714P+ Brochure preview
AirPlus DI-714P+
Бренд: D-Link Страницы: 5
D-Link AC5300 Quick Install Manual preview
AC5300
Бренд: D-Link Страницы: 12
D-Link SharePort DIR-825 Configuring preview
SharePort DIR-825
Бренд: D-Link Страницы: 20
D-Link Express EtherNetwork DI-604 Owner'S Manual preview
Express EtherNetwork DI-604
Бренд: D-Link Страницы: 49
Ebyte E01-ML01DP5 User Manual preview
E01-ML01DP5
Бренд: Ebyte Страницы: 10
M Box D446559XA Operating Manual preview
D446559XA
Бренд: M Box Страницы: 60
Deliberant DLB70XX User Manual preview
DLB70XX
Бренд: Deliberant Страницы: 69
Ruckus Wireless ZoneFlex 2741 Getting Started Manual preview
ZoneFlex 2741
Бренд: Ruckus Wireless Страницы: 58
Zte Z291DL User Manual preview
Z291DL
Бренд: Zte Страницы: 51
DQ Technology M625N User Manual preview
M625N
Бренд: DQ Technology Страницы: 43

Бренды по названию

Популярные бренды

Загрузить еще бренды