39 / EN
Washer-Dryer / User’s Manual
There is detergent left on the laundry.
• Machine might have been overloaded. >>> Do not overload
the machine.
• Wrong programme and temperature might have been selected.
>>> Select the right programme and temperature for the
laundry to be washed.
• Wrong detergent might have been used. >>> Select a proper
detergent for the laundry to be washed.
Too much foam forms in the machine. (**)
• Improper detergents for the washing machine might have been
used. >>> Use detergents suitable for washing machine.
• Excessive amount of detergent might have been used. >>>
Use only sufficient amount of detergent.
• Detergent might have been stored under inappropriate
conditions. >>> Keep the detergent in a closed and dry area.
Do not store it in excessively hot places.
• Meshed laundry such as tulles might foam too much due to
their texture. >>> Use less detergent for these types of fabrics.
• Detergent might have been put in the wrong compartment.
>>> Put the detergent in the correct compartment.
• Softener is taken early. >>> There might be a problem with the
valves or the detergent drawer. Call the Authorised Service Agent.
Foam is overflowing from the detergent drawer.
• Excessive amount of detergent might have been used.
>>>>Mix 1 tablespoonful softener and ½ l water and pour
into the main wash compartment of the detergent drawer.
• Put detergent into the machine suitable for the programmes
and maximum loads indicated in the “Programme and
consumption table”. If you use additional chemicals (stain
removers, bleaches and etc), reduce the amount of detergent.
Laundry remains wet at the end of the programme. (*)
• Excessive foam might have formed due to use of too much
detergent, and the automatic foam absorption system might have
been activated. >>> Use the recommended amount of detergent.
(*) Machine does not switch to spinning step
when the laundry is not evenly distributed in the
drum to prevent any damage to the machine
and to its surrounding environment. Readjust
the laundry and perform spinning again.
(**) The drum might not have been cleaned
regularly.
>>>
Clean the drum regularly. See 6.2
A
CAUTION!
•
If you cannot eliminate the problem
although you follow the instructions in
this section, consult your dealer or the
Authorised Service Agent. Never try to
repair a nonfunctional product yourself.
Drying lasts too long.
• Machine might have been overloaded. >>>
Do not
overload the machine.
• Spinning might not be sufficient for laundry. >>>
Select
a higher spin speed in the washing step of the Washer-Dryer.
• Tap might be turned off. >>>
Turn on the taps.
Laundry comes off wet after the drying step.
• The programme selected might not be suitable for the type
of laundry. >>>
Check the care labels on garments and select a
programme accordingly, or select timed programmes additionally.
• Machine might have been overloaded. >>>
Do not
overload the machine.
• Spinning might not be sufficient for laundry. >>>
Select
a higher spin speed in the washing step of the Washer-Dryer.
Machine does not start or programme cannot be started.
• Power cable might be unplugged. >>>
Make sure that
the power cable is plugged in.
• Programme might not be set, or the Start/Pause/
Cancel button might not be pressed. >>>
Make sure the
programme is set and the machine is not in Stand-by mode.
• Child lock might be enabled. >>>
Disable Child Lock.
Laundry shrinks, fades, tarnishes or gets damaged.
• The programme selected might not be suitable for the type
of laundry. >>>
Check the care labels on garments and select a
programme accordingly, or select timed programmes additionally.
You should not dry laundry that is not suitable for drying.
Machine does not dry.
• Laundry might not be dried or the drying step might not
be enabled. >>>
Check if the drying function is selected
after the selected washing programme.
Loading door cannot be opened.
• The door of your machine might not be opening due to
safety reasons. >>>
If the door locked indicator is active
on the display after the drying step, the machine will keep the
door locked for your safety until it cools down.
• The loading door will not open if there is no power.
>>>
To open the loading door, open the pump filter cap and
pull down the emergency handle positioned at the rear side of
the said cap. See “Loading door lock”
A
WARNING!
•
Check the HomeWhiz section for the
relevant troubleshooting information.
