Beko DIS15010 страница 30 Скачать руководство пользователя

Страница: 30 / 41

There might be residues of

detergent or rinse aid in the

machine and/or on the pieces

being washed depending on the

step the programme you have

cancelled was in.

Salt indicator ( )

Please check the salt indicator on

the display to see whether there is

adequate amount of softening salt

in the dishwasher or not. You need

to refill the salt reservoir with salt

whenever salt indicator appears on

the display of your machine.

Adjusting the water hardness

level is explained in Water

Softening System section.

Rinse Aid indicator ( )

Please check the rinse aid indicator

on the display to see whether there

is adequate amount of rinse aid in the

dishwasher or not. You need to refill

the rinse aid reservoir with rinse aid

whenever rinse aid indicator appears

on the display of your machine.

End of programme

When the programme you have

selected comes to an end, an

audible warning signal will warn

you to turn off your machine. This

audible signal will warn you with

certain intervals before it turns

off.

End of Programme indicator will light

up when the washing programme is

over.

1. Open the door of the machine.
2. Press On/Off key to turn off your

machine.

3. Close the tap.
4. Unplug the machine from the

socket.

For energy saving, the machine is

automatically turned off following

the completion of the programme

or if the programme is not started.

Leave your dishes in the machine

for about 15 minutes to allow

them cool down after they are

washed. Your dishes will dry in a

shorter time if you leave the door

of your machine ajar during this

period. This process will increase

the drying effectiveness of your

machine.

Water cut-off warning

If mains water is cut or water inlet

tap is turned off the machine cannot

take water in and P2 icon will flash

on the programme indicator. As

long as the problem continues,

washing programme is paused and

the water inlet is checked regularly

by the machine; when the water is

restored P2 icon will disappear after

a while and the washing programme

resumes.

Overflowing warning

If the machine intakes too much

water or there is leakage at any of

the components then the machine

will detect this and P1 icon will flash

on the Programme indicator. As long

as the overflowing continues safety

algorithm will be active and try to

discharge the water. If overflowing

stops and safety is assured, P1

icon will disappear. If P1 does not

disappear, there is a permanent fault.

In this case the authorised service

should be contacted.

Содержание DIS15010










































Результаты поиска

Содержание DIS15010

Отзывы:

Похожие инструкции для DIS15010

Бренды по названию

Популярные бренды

Beko DIS15010, Инструкция по эксплуатации

Результаты поиска

Содержание DIS15010

Отзывы:

Похожие инструкции для DIS15010

Бренды по названию

Популярные бренды