Beko DIN26220 страница 45 Скачать руководство пользователя

Страница: 45 / 47

Dishes are scratched.

Kitchen utensils that contains or are made of aluminum should not be

washed in dishwasher.

• Salt leakage exists. >>> Pay attention not to spill salt around the salt filling

hole while adding salt. Spilled salt can cause scratches. Make sure that the

salt reservoir lid is tightly closed after finishing the filling process. Run the

prewash programme to remove the salt that spilled inside the machine.

Since the salt granules that will remain under the lid will dissolve during

prewash, causing the lid loosen, check the lid once again at the end of the

programme.

• Water hardness setting is low or salt level is insufficient >>> Measure the

hardness of the supply water appropriately and check the water hardness

setting.

• Dishes are not placed orderly in the machine. >>> When placing the glasses

and other glassware into the basket lean them not against other dishes but

the edges or racks of the basket or the glass support wire. Striking of the

glasses to each other or to other dishes due to the impact of water during

washing can cause breaks, or scratches on their surfaces.

A smear remains on glasses that resembles milk stain which can not

be removed when wiped by hand. A bluish / rainbow appearance

occurs when the glass is pointed to light.

• Excessive rinse aid is used. >>>Lower rinse aid setting. Clean the spilled

rinse aid when adding rinse aid.

• Corrosion has occurred on glass due to soft water. >>> Measure the

hardness of the supply water appropriately and check the water hardness

setting. If your supply water is soft (<5 dH), do not use salt. Choose

programmes that wash in higher temperatures (e.g. 60-65°C). You can also

use glass protective detergents that are commercially available.

Foam forms in the machine.

• Dishes are washed with hand-wash detergent by hand but not rinsed before

placing them into the machine. >>> Hand-wash detergents do not contain

antifoam. There is no need to hand-wash the dishes before placing them

into the machine. Removing the coarse soil on the dishes under tap water,

with a tissue paper or fork will be sufficient.

• Rinse aid has spilled into the machine when adding rinse aid. >>> Take care

that rinse aid is not spilled in the machine when you are filling it. Clean any

spilled rinse ait with the help of a tissue paper/towel.

• Lid of the rinse aid reservoir is left open. >>> Make sure that the lid of the

rinse aid reservoir is closed after adding rinse aid.

Содержание DIN26220
















































Результаты поиска

Содержание DIN26220

Отзывы:

Похожие инструкции для DIN26220

Бренды по названию

Популярные бренды

Beko DIN26220, Инструкция по эксплуатации

Результаты поиска

Содержание DIN26220

Отзывы:

Похожие инструкции для DIN26220

Бренды по названию

Популярные бренды