background image

7 / EN

Washing Machine / User’s Manual

4.1 Installation

•  Preparation of the location and electrical, tap water and waste water installations at the place of installation 

is under customer's responsibility. 

•  Make sure that the water inlet and discharge hoses as well as the power cable are not folded, pinched or 

crushed while pushing the product into its place after installation or cleaning procedures. 

•  Prior to installation, visually check if the product has any defects on it. If so, do not have it installed. 

Damaged products cause risks for your safety.

4.1.1 Appropriate installation location

•  Place the product on a hard and level floor. Do not put it onto a carpet with high pile or other similar 

surfaces.

•  When the washing machine and dryer are placed on top of each other, their total weight –when loaded– 

amounts to 180 kilograms. Place the product on a solid and flat floor that has sufficient load carrying 

capacity!

•  Do not place the product on the power cable.

•  Do not install the product in the environments where the temperature falls below 0 ºC.

•  Leaving a gap at the sides of the machine is suggested to reduce vibration and noise

•  On a graduated floor, do not place the product next to the edge or on a platform.

•  Do not place heat sources such as Hobs, Irons, Ovens, etc. on the washing machine and do not use them 

on the product.

4.1.2 Removing packaging reinforcement

Tilt the machine backwards to remove the packaging reinforcement. 
Remove the packaging reinforcement by pulling the ribbon. Do not make 
this operation alone by yourself. 

4.1.3 Removing the transportation locks

Loosen all bolts with an appropriate wrench until they turn freely.

Remove the transport safety bolts by turning them slightly.

Insert the plastic covers in the bag containing the user manual to the openings on the rear panel.

A

CAUTION: 

Remove the transportation safety bolts before operating the washing machine! Otherwise, the product will be 

damaged.

C

Keep the transportation safety bolts in a safe place to reuse when the washing machine needs to be moved again in the 
future.
Install the transport safety bolts in reverse order of the disassembly procedure.
Never move the product without the transportation safety bolts properly fixed in place!

Содержание BFL103ADW





































Отзывы: