Beko BEKOMAT BM13i Скачать руководство пользователя

Страница: 71 / 76

15. Troubleshooting and fault repair / FAQ

Error or fault pattern

Possible causes

Troubleshooting

n = ∞

• Negative power-on self-test.

The electronics unit is
defective.

• Contact

BEKO

TECHNOLOGIES customer

service (see “1.1 Contact” on Page 5).

•

All LEDs are off.

•

Read off the operating voltage on the type

plate and check it.

• Check whether voltage is applied to the

terminals of the power control board (GND,
+24 VDC).

• Check the connection terminals on the power

control board.

• All LEDs are on continuously.

• Disconnect the product from the voltage

supply and reconnect after >5 seconds.

• Inspect the circuit board for potential

damage.

• No condensate is drained after

the TEST button has been
pressed.

•  Check the feed line and the drain line.
•  Replace wear parts.
•  Check the valve function by pressing the

TEST button.

Valve switching can be heard clearly
(clicking sound).

• Check the connection terminals on the

control circuit board.

• Condensate is only drained

when the TEST button is
pressed.

• Install the feed line at a slope >3 %.
• Check whether the necessary minimum

pressure has been reached (see “4. Technical
data” on Page 27).

• Replace wear parts.

• The

BEKOMAT

discharges

continuously.

•  Clean the complete valve unit.
•  Replace wear parts.
•  Clean the sensor tube.

Original installation and operation manual

BEKOMAT

13i / 13i CO / 13i CO PN50

71 | 76

Содержание BEKOMAT BM13i













































































Результаты поиска

Содержание BEKOMAT BM13i

Отзывы:

Похожие инструкции для BEKOMAT BM13i

Бренды по названию

Популярные бренды

Beko BEKOMAT BM13i, Перевод оригинального руководства по установке и эксплуатации

Результаты поиска

Содержание BEKOMAT BM13i

Отзывы:

Похожие инструкции для BEKOMAT BM13i

Бренды по названию

Популярные бренды