Beko BEKOMAT BM13i Скачать руководство пользователя | Manualshive

Страница: 58 / 76

background image

10.3.5 Cleaning

CAUTION

Inappropriate cleaning and use of the wrong cleaning media!

Inappropriate cleaning and the use of the wrong cleaning media may result in minor injuries
as well as damage to health and damage to property.
• Never clean the device with a dripping wet cloth.
• Never use abrasive or aggressive cleaning agent or solvents which could damage the

outer coating (e.g. markings, type plate, corrosion protection, etc.).

•  Never clean the device with hard or pointed implements.
•  Use an anti-static, damp cloth for cleaning the outside.
•  Immediately replace any product markings (pictograms, markings) that have become

illegible.

NOTE

Local hygiene regulations!

In addition to the cleaning instructions listed, any regionally applicable hygiene regulations
must be observed.

Prerequisites

Tools

Material

Protective equipment

• Cleaning brush

• Mild cleaning agent
• Cotton or disposable cloth

Always to be worn:

Preparatory tasks

1.

Decommissioning and disassembly of the

BEKOMAT

®

have been completed.

2.

The

BEKOMAT

®

is disassembled.

Cleaning work

Illustration

Description / explanation

1. Spray mild cleaning agent onto a cotton cloth or

disposable tissue until it is damp (not wet). Rub the
surfaces of the

BEKOMAT

®

with a damp cloth.

2. Clean the control-air bore and the condensate

discharge bore using a cleaning brush Ø max. = 2.5 mm

(0.09").

BEKOMAT

®

13i / 13i CO / 13i CO PN50

Original installation and operation manual

58 | 76

«
...
56
57
58
59
60
...
»

Содержание BEKOMAT BM13i













































































Отзывы:

Нет отзывов

Похожие инструкции для BEKOMAT BM13i

Бренд: Maag Страницы: 16

Бренд: Ultranatura Страницы: 24

Бренд: Danfoss Страницы: 64

Бренд: Danfoss Страницы: 86

Бренд: Danfoss Страницы: 28

Бренд: Lasko Страницы: 4

TORNADO 2 Series

Бренд: Larius Страницы: 32

Бренд: Waterous Страницы: 10

Бренд: YAMADA Страницы: 14

Бренд: Kamco Страницы: 36

Бренд: Pelonis Страницы: 24

Бренд: Danner Страницы: 2

Бренд: F.F. Group Страницы: 28

AquaMax Eco Expert 20000/12V

Бренд: Oase Страницы: 231

Бренд: Waeco Страницы: 20

Бренд: Zibro Страницы: 14

WS G140DC6 Series

Бренд: Waterstage Страницы: 64

Under Desk Heater

Бренд: Warmly Yours Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды