Beko BEKOMAT BM13i Скачать руководство пользователя

Страница: 20 / 76

3.5 Modbus function

The

BEKOMAT

has an integrated Modbus which can be used to read out the operating parameters and device

information.
The

BEKOMAT

is operated using the client-server system with operating mode Modbus-RTU.

Data is transmitted via an RS485 interface in binary format.

3.5.1 Default interface parameters

The

BEKOMAT

is available via Modbus 10 seconds after start-up with the following interface parameters.

Value

Parameter

Baud rate

19200

Data bits

Stop bits

Parity

even

Client address

247

3.5.2 Byte sequence

Data type

Modbus register

Division

float

2 Register

ABCD

u32

2 Register

ABCD

u16

1 Register

3.5.3 Implemented functions

The following Modbus functions are supported:
1. Read Input Registers (0x04)
2.

Read Device Identification (0x2B / 0x0E)

3. Changing interface parameters

BEKOMAT

13i / 13i CO / 13i CO PN50

Original installation and operation manual

20 | 76

Содержание BEKOMAT BM13i













































































Результаты поиска

Содержание BEKOMAT BM13i

Отзывы:

Похожие инструкции для BEKOMAT BM13i

Бренды по названию

Популярные бренды

Beko BEKOMAT BM13i, Перевод оригинального руководства по установке и эксплуатации

Результаты поиска

Содержание BEKOMAT BM13i

Отзывы:

Похожие инструкции для BEKOMAT BM13i

Бренды по названию

Популярные бренды