Beko Bekomat 14 Скачать руководство пользователя

Страница: 20 / 64

6. Assembly

6.1 Warning notices

DANGER

Use of incorrect spare parts, accessories or materials!

The use of incorrect spare parts, accessories or materials, as well as auxiliary and operating

materials, may result in death or serious injury. Malfunction and device failure as well as

material damage can occur.
• For all work, only use undamaged original parts, auxiliary and operating materials which

are specified by the manufacturer.

• Use only the approved materials and suitable tools for the respective purpose and make

sure that they are in proper working order.

• Only use pipes that are free of dirt, damage and corrosion.

DANGER

Pressure build-up in the pipework!

Death or serious personal injury can result through contact with fast or suddenly escaping

compressed gas or through bursting system parts.
• All work on the compressed gas system must be carried out in the depressurised state

and with the compressed gas system secured against unintentional pressure build-up.

• Set up a safety area around the working area during all assembly, installation,

maintenance and repair work.

• Before building up pressure in the pipework, check all pipe connections and tighten if

necessary.

• Slowly pressurise the system with pressure.

•

Avoid pressure blows and high differential pressures.

• Assemble all pipelines without stress.

• Install pipes tightly as feed and discharge lines.

WARNING

Insufficient qualification!

Insufficient qualification of the personnel carrying out work on the product and accessories

can lead to accidents, personal injury and damage to property as well as impair operation.
• All work on the product and accessories may only be carried out by skilled technical

personnel - compressed gas technology.

CAUTION

Inappropriate assembly!

Inappropriate assembly of the product and the accessories can lead to personal injury and

damage to property as well as impair operation.

•

Fix hoses in such a way that they do not flap around.

BEKOMAT

13, 13 CO, 13 CO PN25, 13 CO PN40

Original installation and operation manual

20 | 64

Содержание Bekomat 14

































































Результаты поиска

Содержание Bekomat 14

Отзывы:

Похожие инструкции для Bekomat 14

Бренды по названию

Популярные бренды

Beko Bekomat 14, Оригинальное руководство по установке и эксплуатации

Результаты поиска

Содержание Bekomat 14

Отзывы:

Похожие инструкции для Bekomat 14

Бренды по названию

Популярные бренды