Beiyuan BQS-1H Скачать руководство пользователя страница 13

Страница: 13 / 17

Page

Troubleshooting Guide

Issue

description

Troubleshooting

Suggested solution

Handpiece

does not start

Power cord is disconnected

Reconnect and ensure the
cord is secure

Switch is not responsive

Replace switch

Wire broken to the switch

Reconnect

Control board issue

Replacement

Handpiece

overheating

First, find out accurately which part of the handpiece is overheating. Do
this by restarting the handpiece after letting it cool down.

Front portion

overheating

May be due to build-up of dust or debris
in the front portion of the handpiece.

Start the handpiece whilst
pressing and sealing the oil
hole with your thumb, fill in
oil from the front of the
handpiece into the body,
then flip the handpiece and
drain thoroughly.

Check to see if the comb and cutter are
sharp, and proper tension was applied

Re-grind the comb and
cutter, lessen tension
pressure

Thumb and

index finger

portion

overheating

Check the center post and center post
nut, ensure there is no foreign object in-
between

Lift the crank spindle, flush
out the foreign object with
lubricant

Check for signs of wear on the center
post or center post nut

Replace with new parts

Tension nut
overheating

Check the tension pin and tension pin
cup, ensure there is no foreign object in-
between

Remove dust and debris,
apply new grease

Check for signs of wear on the tension
pin or tension pin cup

Replace with new parts

Middle finger
or ring finger

portion

overheating

Check to see if the roller is installed
correctly (make sure the flat side is
facing the crank spindle)

Reinstall the roller

May be due to wool getting caught in the
roller

Remove the wool

A lack of lubrication for cogs in gearbox

Apply lubrication

Содержание BQS-1H


















Результаты поиска

Содержание BQS-1H

Отзывы:

Бренды по названию

Популярные бренды

Beiyuan BQS-1H, Инструкция по эксплуатации

Результаты поиска

Содержание BQS-1H

Отзывы:

Бренды по названию

Популярные бренды