Beijing TT Aviation Technology TIANNONG M6E-X страница 21 Скачать руководство пользователя

Страница: 21 / 73

Beijing TT Aviation Technology Co., Ltd.

Add: No.1 TTA Building, Niantou Industrial Park ,Changping District,Beijing, China

www.ttaviation.org

3.3 Charging

1) Electric indicator will flash in cycle and displays the current electric quantity.

2) It means the intelligent battery has been fulled when electric indicator is OFF.Please

take down the charger and charging has been finished.

3) The charging temperature of intelligent battery is 10

℃

to 40

℃

,it’s forbidden to charge

above 45

℃

or less than 5

℃

4) Please do not charge the battery without people.

5) Forbid to charge with the output connector and forbid to use the battery power when

charging.

Attention:

Please disconnect the discharging cable before charging.

Indicator

LED1-LED4

Battery

Electricity

Green

LED1

Green

LED2

Green LED3

Green

LED4

0%~25%

Flash

OFF

26%~50%

Flash

OFF

51%~75%

Flash

OFF

76%~99%

Flash

100%

OFF

3.3.1 Charging Protection Function

1) The best charging current for intelligent battery is 0.5C, and 25A is maximum current

supported. Large charging current will not benefit to prolong battery lifetime. It’s

forbidden to charge higher than Max charging current.

2) If there is abnormal (e.g., short circuit of charging end) during charging status,stop

charging immediately. Inspect battery status and contact TTA engineer for further check

before continuing charging.

Содержание TIANNONG M6E-X









































































Результаты поиска

Содержание TIANNONG M6E-X

Отзывы:

Похожие инструкции для TIANNONG M6E-X

Бренды по названию

Популярные бренды

Beijing TT Aviation Technology TIANNONG M6E-X, Инструкция пользователя

Результаты поиска

Содержание TIANNONG M6E-X

Отзывы:

Похожие инструкции для TIANNONG M6E-X

Бренды по названию

Популярные бренды