Beijing StarFire Control Technology Co., Ltd. SF-2012AH-QG Скачать руководство пользователя страница 44 | Manualshive

Страница: 44 / 61

background image

Beijing Starfire Control Technology Co.,Ltd.

北京斯达峰控制技术有限公司

Model SF-2012AH-QG

Cutting Machine

（

C002

）

26

【

F8

】

Submit:

After parameters are set, press this key to generate machining program.

8.

４

. User Defined Module

User is allowed to customize module with the following method .

1)

Firstly, it is required to edit a standard program for the self-defined module and name it as TK17S.NC, which

should have the following structure:
G92 X0 Y0

// User-defined module, Note: The original program should not have more than 59 lines.

G28

// The last line should command the torch to return to the reference point.

M02

2)

Simply copy this program into the file system. The 17th pattern element is self-defined. If no new module is

self-defined, the system will take the old module automatically.

3)

This module is allowed to use for Layout and Rotate features, but no parameter to set .

«
...
42
43
44
45
46
...
»

Содержание SF-2012AH-QG






























































Отзывы:

Нет отзывов

Похожие инструкции для SF-2012AH-QG

Бренд: KELCO Страницы: 36

Бренд: E-fly Страницы: 16

Бренд: Eaton Страницы: 8

Slim Remote Control

Бренд: Packard Bell Страницы: 2

Бренд: Unipower Страницы: 24

Бренд: Paradox Страницы: 2

Бренд: Parkside Страницы: 86

disklavier DKC-850

Бренд: Yamaha Страницы: 2

Бренд: Full Gauge Controls Страницы: 3

Бренд: MAHA Страницы: 23

Бренд: Sherlotronics Страницы: 2

Бренд: Valcom Страницы: 9

Бренд: GCE Страницы: 13

Бренд: Leviton Страницы: 2

Бренд: TECH Страницы: 20

Бренд: Pro-face Страницы: 48

Бренд: Allen-Bradley Страницы: 226

Therm-O-Flow Series

Бренд: Graco Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды