JetNet 6528Gf Series Industrial 28G Full Gigabit Managed Ethernet Switch
Quick Installation Guide V1.1
The JetNet 6528Gf Series is a 19-inch Industrial 28G Full Gigabit Managed Ethernet Switch
equipped with 24 100/1000TX, 8 100/1000 RJ-45/SFP combo ports, 4 GbE SFP ports.
Dimension
JetNet 6528Gf Industrial 28G Full Gigabit Managed Ethernet Switch dimension (W x H x
D) is 44mm(H) x 438mm (W) x 375mm (D).
Front-Panel Components
The front panel includes RJ-45 based RS-232 console port, USB port, System & port LEDs,
Gigabit Ethernet port Interfaces and Gigabit combo port Interfaces.
LED Indicators
Back-Panel Components
The back panel of the JetNet 6528Gf Industrial 28G Full Gigabit Managed Ethernet Switch
consists of AC power input, DC power input and relay output depend on different Model.
JetNet 6528Gf-2AC:
JetNet 6528Gf-2DC24/48:
Package Check List
The Rack Mount Managed Ethernet Switch
Console cable
Rack Mount kit
Power Cord (Depend on Country, JetNet 6528Gf-2DC24/48 no Power Cord)
QIG
Overview
Interface Introduction
A Beijer Electronics Group Company
Installation
Mount the Switch to 19’’ rack
1. Attach the brackets to the device by using the
screws provided in the Rack Mount kit.
2. Mount the device in the 19’’ rack by using four
rack-mounting screws provided by the rack
manufacturer.
3. When installing multiple switches, mount them in
the rack one below the other.
Power the unit and connect to network Cable
AC Power Input: connect the attached power cord to the AC power input connector, the
available AC power input is range from 90-264VAC.
DC Power Input: the suggested power input is 24VDC/48 VDC, the available range is from
18-36VDC/ 36-75VDC.
Follow below steps to wire JetNet 6528Gf redundant DC power inputs.
1. Insert positive and negative wires into V+ and V- contacts respectively of the terminal
block connector.
2. Tighten the wire-clamp screws to prevent DC wires from being loosened.
3. DC1 and DC2 support polarity reverse protection functions.
Wiring Digital Output
JetNet 6528Gf series provides 1 digital output, also known as relay output. The relay
contacts are energized (open) for normal operation and will close for fault conditions. The
fault conditions include power failure, Ethernet port link break or other pre-defined events
which can be configured in JetNet 6528Gf UI.
Wiring Earth Ground
To ensure the system will not be damaged by noise or any electrical shock, we suggest you to
make exact connection with JetNet 6528Gf with earth ground.
For AC input, the 3 pin include V+, V- and GND. The GND pin must be connected to the
earth ground.
For DC input, loosen the earth ground screw by screw drive; then tighten the screw after
earth ground wire is connected.
Note:
Check if the rack environment temperature conforms to the specified operating
temperature range. Do not place any equipment on top of the switch and please properly
grounded.
24 100/1000TX, 8 100/1000 RJ-45/SFP combo ports, 4 GbE SFP ports,
Ind. full Gigabit Managed Ethernet Switch, -40~75°C, AC power
24 100/1000TX, 8 100/1000 RJ-45/SFP combo ports, 4 GbE SFP ports,
Ind. full Gigabit Managed Ethernet Switch, -40~75°C, dual AC power
24 100/1000TX, 8 100/1000 RJ-45/SFP combo ports, 4 GbE SFP ports,
Ind. full Gigabit Managed Ethernet Switch, -40~75°C, AC and DC power
24 100/1000TX, 8 100/1000 RJ-45/SFP combo ports, 4 GbE SFP ports,
Ind. full Gigabit Managed Ethernet Switch, -40~75°C, dual DC power
Model Name
Description
JetNet 6528Gf-2AC
JetNet 6528Gf-AC
JetNet 6528Gf-AC-DC24
JetNet 6528Gf-2DC24/48
1 AC power inputs and 1 relay output.
2 AC power inputs and 1 relay output.
1 AC power inputs, 1 DC power inputs and 1 relay output.
2 DC power inputs and 1 relay output.
JetNet 6528Gf-AC
JetNet 6528Gf-2AC
JetNet 6528Gf-AC-DC24
JetNet 6528Gf-2DC24/48
Model Name
Back-Panel Components
1A@24V
--<-
1A@24V
--<-
18-36VDC
90-264VAC, 50-60Hz
PWR2
PWR3
PWR4
PWR1
90-264VAC, 50-60Hz
G2
G4
G6
G8
G10
G12
G14
G16
G18
G20
G22
G24
G18
G20
G22
G24
G26
G28
Alarm
Sys
R.S.
LNK/ACT
Speed
G1
G3
G5
G7
G9
G11
G13
G15
G17
G19
G21
G23
G17
G19
G21
G23
G25
G27
Console
USB
Industrial 28G Full Gigabit
Managed Ethernet Switch
PWR
1
2
3
4
G17
G18
G19
G20
G21
G22
G23
G24
G25
G26
G27
G28
G2
G4
G6
G8
G10
G12
G14
G16
G18
G20
G22
G24
G18
G20
G22
G24
G26
G28
Alarm
Sys
R.S.
LNK/ACT
Speed
G1
G3
G5
G7
G9
G11
G13
G15
G17
G19
G21
G23
G17
G19
G21
G23
G25
G27
Console
USB
Industrial 28G Full Gigabit
Managed Ethernet Switch
PWR
1
2
3
4
G17
G18
G19
G20
G21
G22
G23
G24
G25
G26
G27
G28
--
<
-
1A@24V
--
<
-
90-264VAC, 50-60Hz
PWR2
PWR1
90-264VAC, 50-60Hz
--
<
-
1A@24V
--
<
-
18-36VDC
PWR3
PWR4
G2
G4
Alarm
Sys
R.S.
LNK/ACT
Speed
G1
G3
Console
USB
Industrial 28G Full Gigabit
Managed Ethernet Switch
PWR
1
2
3
4
G26
G28
G25
G27
G25
G26
G27
G28
LED
Color
Function
PWR
Green
Power (AC1, AC2, DC1, DC2) on
Alarm
Red
Power failure, port failure, ping failure,
login failure, RSR topology change
R.S.
Lit Green
MSR in normal state
Lit Yellow
MSR in abnormal state
Not Lit
MSR function not active
Flashes Green
Incorrect configuration of MSR, ex. ring not
connected to ring port
Flashes
Yellow
The break has been detected to be local to
one of the ports
Sys
Green
System on
G1-G24 Copper
LNK/ACT
Lit Green
10/100/1000 RJ-45 Link
Flashes Green
10/100/1000 RJ-45 Activity
G1-G24 Copper
Speed
Yellow on
1000Mbps
Yellow off
10/100Mbps
G17-G28 SFP
LNK/ACT
Lit Green
Link
Flashes Green
Activity
