Beijer Electronics BFI-E3 Series, Стартап

Страница: 23 / 28

Beijer Electronics Frequency Inverter BFI-E3
KI00369C 2021-09
www.beijer.se www.beijer.no www.beijer.dk www.beijerelectronics.de www.beijerelectronics.com www.beijerelektronik.com.tr
23 (28)
6.1 LED Display
BFI-E3 has a built-in 6 Digit 7 Segment LED Display. On theright side of each digit there is a
dot indicating status in BFI according to table below:
6.2 Monitoring from Keypad
Put P14=201 to access monitor values in parameter group P0. Here are a few of what can be monitored
Par Description Display range Explanation
P0-01
1st Analog Input Value
0 … 100%
100% = max input voltage
P0-02
2nd Analog Input Value
0 … 100%
100% = max input voltage
P0-03
Speed Reference Input -P-
01 … P-01
Displayed in Hz if P-10 = 0, otherwise displayed in RPM
P0-04
Digital Input Status Binary value Drive digital input status
P0-05
User PI output (%)
0 … 100%
User PI output (%)
P0-06
DC bus ripple (V)
0 … 100%
DC bus ripple (V)
P0-07
Applied Motor Voltage
0 … 600V AC
Value of RMS voltage applied to motor
P0-08
DC Bus Voltage
0 … 1000V dc
Internal DC bus voltage
P0-09
Heatsink temperature -
20 … 120 °C Temperature of heatsink in ᵒC
P0-10
Hours Run Meter 0 to 99 999 hours Not affected by resetting factory default parameters
P0-13
Trip Log 0 to 99 999 hours Displays most recent 4 trips with time stamp
P0-15
DC Bus Voltage Log
0 … 1000V
8 most recent values prior to trip, updated every 256ms
P0-16
Heatsink Temperature Log -
20 … 120 °C
8 most recent values prior to trip, updated every 30s
P0-17
Motor Current 0 to 2x rated current 8 most recent values prior to trip, updated every 256ms
P0-18
DC bus ripple log (V)
0 … 100%
8 most recent values prior to trip, 22ms sample time
P0-19
Internal drive temperature log -
20 … 120 °C
8 most recent values prior to trip, 30 s sample time
P0-20
Internal drive temperature -
20 … 120 °C Actual internal ambient temperature in ᵒC
P0-23
Temperature log cooling fin Hours:min Total time of operation above heatsink temp of 85
ᵒC
P0-24
Temperatur log internally Hours:min Total time of operation with internal temperatur above 80
ᵒC
P0-25
Estimated rotor speed
0 … 500 Hz
In vector control modes, estimated rotor speed in Hz
P0-28
Software version
e.g. “1.00”, “47AE” “1”: Indicates I/O processor, “2“ : Indicates power stage
P0-29
Drive type identifier BFI type, Drive rating, input phases, voltage, firmware
P0-30
Drive serial number xxxxxx / yy / zzz Unique drive serial number
P0-31
Motor current Id / Iq 0 to 2x rated current Displays magnetising current (Id) and torque current (Iq).
P0-33
Critical fault counter
– O-I
Number of times Number of trips due to overcurrent
P0-34
Critical fault counter
– O-Volts
Number of times Number of trips due to over voltage
P0-35
Critical fault counter
– U-Volts
Number of times Number of trips due to under voltage
P0-36
Critical fault counter
– O-temp
Number of times Number of trips due to over temperature heatsink
P0-38
Error counter
– O-hEAt
Number of times Number of trips due to internal over temperature