Becx Machines OBKS50-35 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 25

Becx Machines OBKS50-35 Скачать руководство пользователя страница 15

Weed brush

–

Edge cutter

OBKS50-35

Version: 1

November ’19

Page 15 of 25

4.

Operations

4.1.

Assembly and adjustment of the weed brush

No.

What to do

Action

Result

1

Select the correct tool
carrier and lifting arm

make sure that the tool carrier and lifting arm
are sufficiently strong and stable for the
weed brush (see chapter 1

Fout! V

erwijzingsbron niet gevonden.

for the load

when lifting and the exerted moment of the
lifting).
Make sure that the maximum pressure and
number of revolutions (oil flow) are not
exceeded.
Make sure that the correct rapid attachment
connections are installed for the feed line,
return line and drain line.
Make sure that the correct clasp is used.

Ignoring the stated
values can result in
damage to
equipment and
injury to persons.

2

Connect the hoses

Connect the rapid attachment connections
for the feed line, return line and drain line .

3

Adjust the hydraulic
system

Adjust the setting of the hydraulic aggregate
so that the maximum pressure and number
of revolutions cannot be exceeded.
This will depend on the type of tool carrier
that is used. Please refer to the manual of the
tool carrier.

4

Adjust the positions
for the blade and
brush

With help of the different hydraulic functions
the blade and brush can be adjusted to
achieve the correct result with the weed
brush.

«
...
13
14
15
16
17
...
»

Содержание OBKS50-35


























Отзывы:

Нет отзывов