manualshive.com logo in svg

Beckman Coulter Microfuge 20 Series, Инструкция по эксплуатации

Поделиться
Скачать
Beckman Coulter Microfuge 20 Series Скачать руководство пользователя страница 63

B30162AA

A-1

APPENDIX A

Installation

Introduction

This chapter contains instructions for installing and connecting the centrifuge. Check that required 
clearances and electrical power are available.

WARNING

Risk of personal injury. Each centrifuge weighs 13 kg/29 lb (nonrefrigerated 
model) or 32 kg/71 lb (refrigerated model.) DO NOT attempt to lift or move one of 
them without assistance from a lifting device or another person.

Installing the Instrument

WARNING

Risk of fire. Do not place the centrifuge near areas containing flammable reagents 
or combustible fluids. Vapors from these materials could enter the centrifuge air 
system and be ignited by the motor.

WARNING

 Maintain a 30 cm (12 in) clearance envelope around the centrifuge while it 
is running. No persons should be within this clearance boundary while the 
centrifuge is operating. Do not handle or store hazardous materials within the 
30 cm (12 in) area surrounding the centrifuge.

Considerations to make before installation

 •

Operate the centrifuge only in closed and dry rooms.

 •

All of the energy supplied to the centrifuge is converted into heat and emitted to the 
ambient air.

 •

Ensure sufficient ventilation.

 •

Allow at least a 30 cm envelope around all sides of the centrifuge so that the vents in the 
centrifuge remain fully effective.

Содержание Microfuge 20 Series











































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды