manualshive.com logo in svg

Beckman Coulter Microfuge 20 Series, Инструкция по эксплуатации

Поделиться
Скачать
Beckman Coulter Microfuge 20 Series Скачать руководство пользователя страница 46

B30162AA

2-16

Operation

Saving and Using Programs  

Saving and Using Programs

The program is used to save or load certain recurring settings of the centrifuge. Ten separate 
programs can be saved and reused.

NOTE

The precooling program does not occupy any storage location and cannot be deleted. It is used only 

to cool the centrifuge without vessels. See 

Precooling the centrifuge (20R refrigerated models only)

.

Saving Settings

The following parameters that are set to be run can be saved as part of a reusable program:

 •

Speed

 •

Run time

 •

Temperature (Microfuge 20R only)

 •

Acceleration

 •

Deceleration

 •

Rotor type/code

To save settings into a program

1

Press the 

PROG

 key.

2

Press the 

 or 

 cursor key to scroll and select an unused program number.

The display 

Prog ##

 flashes (# represents numbers 01 through 10).

NOTE

Scrolling through the programs causes the parameters of each program to display.

NOTE

Program numbers that are already occupied will be overwritten with the current data.

NOTE

The programs that are not in use display the default settings. See 

Entering Run Parameters

 for 

the default settings.

3

Using the 

MENU

 key and the 

 or 

 cursor keys, change speed, time, temperature, and/or 

acceleration parameters. See 

Entering Run Parameters

 for details.

4

Press the 

MENU

 key to confirm the selections and the program. The program is saved.

Содержание Microfuge 20 Series











































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды