manualshive.com logo in svg

Beckman Coulter Microfuge 20 Series, Инструкция по эксплуатации

Поделиться
Скачать
Beckman Coulter Microfuge 20 Series Скачать руководство пользователя страница 32

B30162AA

2-2

Operation

Run Procedure  

WARNING

Risk of personal injury or property damage. The centrifuge must not be used in the 
vicinity of flammable liquids or vapors, and such materials should not be run in the 
centrifuge. During operation you should come within the 30 cm (12 in.) clearance 
envelope only to adjust the instrument controls, if necessary. Never bring any 
flammable substances within the 30 cm (12 in.) area surrounding the centrifuge. 
Do not lean on the centrifuge or place items on the centrifuge while it is operating.

Run Procedure

The following detailed operating procedures are summarized at the end of this section. If you 
are an experienced user of this centrifuge, you can turn to the summary for a quick review of 
operating steps.

Preparation and Loading

NOTE

Before installing the rotor, lubricate it following the instructions in the rotor manual.

1

Check the name rating plate for the correct voltage, then plug the power cord into the wall 
receptacle.

2

Press the power switch to on (

I

).

3

Press the 

OPEN

 key and lift the door up; it remains in the open position.

4

Use the T-handle wrench to turn the rotor tie-down screw to the left (counterclockwise). 

a.

Remove the tie-down screw.

5

Remove the rotor.

Содержание Microfuge 20 Series











































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды