Beckman Coulter Avanti J-26 XP Series Скачать руководство пользователя страница 55

Страница: 55 / 76

J326XP-IM-5AB

4-1

CHAPTER 4

Troubleshooting

Introduction

This chapter lists possible malfunctions, along with probable causes and corrective actions. Maintenance
procedures are given in

CHAPTER 5, Care and Maintenance

. For any problems not covered here, contact

Beckman Coulter Field Service (1-800-742-2345 in the United States for assistance.

NOTE

It is your responsibility to decontaminate the instrument, as well as any rotors and/or accessories,

before requesting service by Beckman Coulter Field Service.

User Messages

If a problem occurs during operation, the appropriate diagnostic message will light and a beep will
sound to alert you to the condition. See

Table 4.1

for a list of the diagnostic messages, the probable

causes, and the recommended actions.

Two kinds of diagnostic conditions can occur.

•

Cautionary diagnostic messages

alert you to a condition that may need attention when the run is

complete. Cautionary diagnostic messages provide information only; they do not shut down the
run in progress. Press

CLEAR

to stop the light from flashing. If the condition still exists, the

diagnostic message will begin flashing again, even though the run continues.

•

Shutdown diagnostic messages

occur when a problem exists that prevents the run from

continuing. The diagnostic message will flash and the red

STOP

key light will also flash,

indicating that the rotor is decelerating to a stop. You can press

CLEAR

to stop the diagnostic

message from flashing. However, if the diagnostic condition still exists (for example, if the rotor
is out of balance), another beep will sound and the message will start flashing again.

CLEAR

POWER

REFR
TEMP

DRIVE

SYS

SPEED

DOOR

IMBAL

FRS

ROTOR

Содержание Avanti J-26 XP Series












































































Результаты поиска

Содержание Avanti J-26 XP Series

Отзывы:

Похожие инструкции для Avanti J-26 XP Series

Бренды по названию

Популярные бренды

Beckman Coulter Avanti J-26 XP Series, Инструкция по эксплуатации

Результаты поиска

Содержание Avanti J-26 XP Series

Отзывы:

Похожие инструкции для Avanti J-26 XP Series

Бренды по названию

Популярные бренды