Beckman Coulter Avanti J-26 XP Series Скачать руководство пользователя страница 42

Страница: 42 / 76

J326XP-IM-5AB

3-2

Operation

Summary of Avanti J-26XP Run Procedures

Summary of Avanti J-26XP Run Procedures

For runs at temperatures other than ambient, precool or prewarm the rotor to the required temperature
before the run.

Press the

POWER

switch to on (

). Open the centrifuge door.

Install the rotor. Make sure that the rotor load is balanced and that the rotor is securely fastened
to the centrifuge drive hub. Close the centrifuge door.

Turn the Rotor knob until the installed rotor name appears in the

ROTOR ID

display.

Turn the

SPEED

knob until the required run speed (rpm) appears in the

SPEED

display. Or press

RPM/RCF

to select

RCF

mode and turn the

SPEED

knob until the required rcf appears in the

SPEED

display.

Turn the

TIME

knob until the required run length appears in the

TIME

display. Or press

TIME/HOLD

for continuous operation.

Turn the

TEMP

knob until the required temperature appears in the

TEMP°C

display.

Press

ACCEL

repeatedly to select

MAX

(maximum) or

SLOW

acceleration.

Press

DECEL

repeatedly to select

MAX

(maximum) or

SLOW

deceleration, or select

OFF

(no brake).

Check that all parameters are correct and that the door is closed. Press

START.

Wait for the set time to count down to zero, or end the run by pressing

STOP

When the run is complete, open the door and unload the rotor.

Содержание Avanti J-26 XP Series












































































Результаты поиска

Содержание Avanti J-26 XP Series

Отзывы:

Похожие инструкции для Avanti J-26 XP Series

Бренды по названию

Популярные бренды

Beckman Coulter Avanti J-26 XP Series, Инструкция по эксплуатации

Результаты поиска

Содержание Avanti J-26 XP Series

Отзывы:

Похожие инструкции для Avanti J-26 XP Series

Бренды по названию

Популярные бренды