background image

Technical data, mounting, wiring

PS1111-2403-0000

21

Version: 1.0

3.13

Environment

Environment

Operating temperature 

1)

-10°C to +70°C

Reduction of the output power according to
Fig. 

Output current over ambient temperature

Storage temperature

-40°C to +85°C

For storage and transport

Output load reduction

0.1A/°C

B60°C and +70°C

Load reduction due to
installation altitude 

3)

0.25A/1000m or 5°C/1000m

Above 2000m, see Fig. 

Output current over

installation altitude

Moisture

5 to 95% r.h.

According to IEC 60068-2-30 Do not
energize if there is condensation.

Atmospheric pressure

110-54kPa

see Fig. 

Output current over installation

altitude

Installation altitude

0 to 5000m

see Fig. 

Output current over installation

altitude

Overvoltage category

II

According to IEC 60664-1, for altitudes up to
5000m

Surge voltage strength

4kV (according to overvoltage
category III)

Input to PE
According to IEC 60664-1, for altitudes up to
2000m

Degree of pollution

2

According to IEC 60664-1, non-conductive

Oscillation, sinusoidal 

2)

2–17.8Hz: ±1.6mm;
17.8-500Hz: 2g 2 hours/axis

According to IEC 60068-2-6

Impacts

2)

30g 6ms, 20g 11ms 3 impacts/
direction, 18 impacts in total

According to IEC 60068-2-27

1)

 The working temperature is identical to the room temperature or the ambient temperature and is defined as

the air temperature 2cm below the device.

2)

 Tested in conjunction with DIN rails according to EN 60715 with a height of 15mm and a thickness of

1.3mm and standard mounting position.

3)

 The derating is not hardware-controlled. The user must take this into account in order to stay below the

reduced current limits, so that device overload is avoided.

Fig. 11: Output current over ambient temperature; output current over installation altitude

Содержание PS1111-2403-0000
































Отзывы: