Beckhoff EM7004 Скачать руководство пользователя страница 22

Страница: 22 / 130

Mounting and wiring

EM7004

Version: 2.0

Optimum installation position (standard)

The optimum installation position requires the mounting rail to be installed horizontally and the connection
surfaces of the EL/KL terminals to face forward (see Fig.

“Recommended distances for standard installation

position”

). The terminals are ventilated from below, which enables optimum cooling of the electronics through

convection. "From below" is relative to the acceleration of gravity.

Fig. 17:

Recommended distances for standard installation position

Compliance with the distances shown in Fig.

“Recommended distances for standard installation position”

recommended.

Other installation positions

All other installation positions are characterized by different spatial arrangement of the mounting rail - see
Fig

“Other installation positions”.

The minimum distances to ambient specified above also apply to these installation positions.

Содержание EM7004



































































































































Результаты поиска

Содержание EM7004

Отзывы:

Похожие инструкции для EM7004

Бренды по названию

Популярные бренды

Beckhoff EM7004, Документация

Результаты поиска

Содержание EM7004

Отзывы:

Похожие инструкции для EM7004

Бренды по названию

Популярные бренды