Beckhoff CX20 2 Series Скачать руководство пользователя страница 39

Страница: 39 / 77

Commissioning

CX20x2

Version: 1.7

6.4

Switching on

Please ensure that the Embedded PC is fully configured before switching on the Embedded PC.

Switch on the Embedded PC as follows:

1. Ensure that all extension, system and fieldbus modules are connected correctly.

2. Check whether the Embedded PC is mounted securely on the DIN rail and all required Bus Terminals

are connected.

3. Only connect the external power supply for the power supply unit after having done so.

The Embedded PC starts automatically as soon as you connect the external power supply for the power
supply unit. The pre-installed operating system is started and all connected extension, system and
fieldbus modules are configured.

6.5

Switching off

NOTE

Loss of data

If the Embedded PC is switched off during operation, data on the CFast card or other hard disks may be
lost.

• Do not disconnect the Embedded PC from the power supply during operation.

Switch off the Embedded PC as follows:

1. Stop all running programs properly, e.g. the control software on the Embedded PC.

2. Shut down the operating system.

3. Switch off the external power supply for the power supply unit last so that the Embedded PC is switched

off.

Содержание CX20 2 Series














































































Результаты поиска

Содержание CX20 2 Series

Отзывы:

Похожие инструкции для CX20 2 Series

Бренды по названию

Популярные бренды

Beckhoff CX20 2 Series, Руководство пользователя

Результаты поиска

Содержание CX20 2 Series

Отзывы:

Похожие инструкции для CX20 2 Series

Бренды по названию

Популярные бренды