manualshive.com logo in svg

Beckhoff CX20 0 Series, Руководство пользователя, Страница: 42 / 92

Поделиться
Скачать
Beckhoff CX20 0 Series Скачать руководство пользователя страница 42

Commissioning

CX20x0

42

Version: 2.5

6.3.1

Connect Embedded PC

The cables of an external voltage source are connected to the power supply unit with spring-loaded
terminals. Observe the required conductor cross-sections and strip lengths.

Table 28: Required conductor cross-sections and strip lengths.

Conductor cross-section

0.5 ... 2.5 mm

2

AWG 20 ... AWG 14

Strip length

8 ... 9 mm

0.33 inch

Fig. 24: Connection example with a CX20x0.

Connect the Embedded PC as follows:

1. Open a spring-loaded terminal by slightly pushing with a screwdriver or a rod into the square opening

above the terminal.

2. The wire can now be inserted into the round terminal opening without any force.

3. The terminal closes automatically when the pressure is released, holding the wire safely and

permanently.

ð

You have successfully connected the voltage source to the power supply terminal when the two upper
LEDs of the power supply terminal light up green.

The left LED (Us 24V) indicates the supply of the basic CPU module and the terminal bus. The right LED
(Up 24V) indicates the bus terminal supply via the power contacts.

6.3.2

UL requirements

The CX20x0 Embedded PCs are UL-certified. The corresponding UL label can be found on the name plate.

Содержание CX20 0 Series





























































































Отзывы:

Нет отзывов