Beckhoff ATH2000-0250 Скачать руководство пользователя страница 59

Страница: 59 / 100

Mechanical installation

Version: 1.0

───

eXtended Transport System

7.4.1

System test

Before beginning with the assembly of the guide rails, check the
functionality of the modules. You can determine whether you have
assembled the modules properly and fully as well as identifying de-
fects.

Power supply

► Connect the entire system 1 to the power supply without guide

rails

► First switch the 24 V on, then the 48 V

► Make sure that the LEDs 2 light up

The following LEDs 2 must light up:

• Link / Act

• 48 V / 16 A

• 24 V / 4 A

If the LEDs do not light up:

► Check the power supply units and fuses for voltage

► Check whether the appropriate covers with connection card have

been inserted

► Contact the Support/Applications Department

TwinCAT

Beckhoff also recommends checking the modules using the Twin-
CAT software.

► Connect EtherCAT connector to the control computer

► Start a TwinCAT project

► Scan the modules

► Check the modules for functionality

Содержание ATH2000-0250





































































































Результаты поиска

Содержание ATH2000-0250

Отзывы:

Beckhoff ATH2000-0250, Руководство по эксплуатации, Страница: 59 / 100

Результаты поиска

Содержание ATH2000-0250

Отзывы: