Beckhoff AMI8100 Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 61

background image

Technical description

Version: 1.0

───

35

AMI8100

7.1

Mounting position

Observe the maintenance intervals and installation positions

Carry out maintenance at regular intervals.
In the horizontal installation position IM V3, liquid which has been
left on the flange for a longer period can penetrate the servo drive
through capillary action. In installation position IM V1 liquid can es-
cape.

If you do not observe the maintenance intervals, the servo drive
may overheat depending on the installation position. Ingress and
leakage of liquids may damage the servo drive.

The standard installation position of the servo drives is the design
IM B5 according to DIN EN 60034-7.

7.2

Feedback

Feedback exchange

The feedback system installed can only be replaced with an identi-
cal system. It is not possible to change the feedback system retro-
spectively.

The table below provides information about system accuracies and
resolutions of the servo drive feedback systems:

Feedback

Resolution

System accuracy

Comment

Encoder, single-turn

Encoder, multi-turn

17-bit

± 316 angular seconds

Standard:

AMI812x

«
...
33
34
35
36
37
...
»

Содержание AMI8100






























































Отзывы:

Нет отзывов

Похожие инструкции для AMI8100

VLT AutomationDrive FC 301

Бренд: Danfoss Страницы: 84

Бренд: YASKAWA Страницы: 18

Бренд: YASKAWA Страницы: 139

Бренд: NI Страницы: 42

Бренд: Ltech Страницы: 7

DL-PS/24-JB-OD-S Series

Бренд: Jesco Страницы: 2

Бренд: Emerson Страницы: 420

Sonesse Ultra 50 RTS

Бренд: SOMFY Страницы: 52

Atrium HS Comfort drive

Бренд: Maco Страницы: 64

Бренд: Danfoss Страницы: 48

Бренд: Parker Страницы: 129

SMARTDRIVE VF1000 M Series

Бренд: Lust Страницы: 78

Бренд: LG Страницы: 16

Бренд: LG Страницы: 55

Бренд: Danfoss Страницы: 20

BRIDGE 0-10V PLC DC STR lp

Бренд: Tridonic Страницы: 4

EiceDRIVER 6ED Series

Бренд: Infineon Страницы: 23

StorageWorks Ultrium 460

Бренд: HP Страницы: 73

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды