Beckhoff AG3300 Скачать руководство пользователя страница 56

Страница: 56 / 68

Mechanical installation

───

Version: 2.5

AG3300

8.3

Gear unit to machine

No washers necessary

Beckhoff recommends not using washers if the material of the
screw contact surface has an adequate interface pressure.

8.3.1

Output side

Avoid damage due to stresses

Use suitable tools for the assembly. Mount gear wheels and
toothed belt pulleys without force on the output shaft and avoid
mounting by driving or hammering on.

The gear unit can be damaged if stress occurs during mounting.

► Seal any gap over a wide area when attaching to the output side

► Make sure that the surfaces of the attached parts have a low

roughness

► Use only screw head seals and o-rings for sealing

8.3.1.1

Permissible axial forces

The following table shows the maximum permissible static axial
forces. The permitted forces refer to the center of the shaft:

Gear unit

005

015

025

035

045

Fa max [N]

1800

4300

5100

11300

18500

Содержание AG3300





































































Результаты поиска

Содержание AG3300

Отзывы:

Похожие инструкции для AG3300

Бренды по названию

Популярные бренды

Beckhoff AG3300, Руководство по эксплуатации

Результаты поиска

Содержание AG3300

Отзывы:

Похожие инструкции для AG3300

Бренды по названию

Популярные бренды