manualshive.com logo in svg

Becker C01, Руководство по сборке и эксплуатации

Поделиться
Скачать
Becker C01 Скачать руководство пользователя страница 13

Readying the tubular drive for programming with the radio switch

Switch the radio switch to the inside position. If the radio switch is already in this posi-
tion, switch it to the outside and back to the inside position.

►

The tubular drive is ready to programme for 3 minutes

Programming the master transmitter

Press the programming button for 3 seconds when it is ready to programme.

▻

The tubular drive acknowledges.

►

The programming process is now complete.

If a transmitter is already programmed on the receiver, press the programming button for

10 seconds.

Checking that the running direction is correct

There are 2 ways to change the direction of rotation:

•

Changing direction of rotation via rotation direction switch

•

Changing direction of rotation via master transmitter

Changing direction of rotation via rotation direction switch

Press the UP or DOWN button

▻

The shading solution runs in the desired direction

►

The running direction is OK.

If the shading solution runs in the wrong direction, the running direction must be changed. Proceed as follows:

Switch the direction switch (1) to the opposite position.

▻

The running direction will now have changed.

►

Check the running direction again.

13

Содержание C01





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды