background image

Attention

For PR+SMI

When using anti-lifting devices, closed brackets must be fitted. The tubular drive presses

the closed curtain down to make it difficult for people to reach under it or raise it. Only use

curtains made of sufficiently strong material, such as aluminium, steel or wood. To prevent

damage to the curtain it must run in guide tracks from top to bottom.

Undoing the mounting pin

When pushed in, the mounting pin (2) locks automatically. To undo the mounting pin
(2), push the tab washer (1) upwards and pull out the mounting pin (2).

Assembling the drive adapter with drive adapter safety catch

Put the drive adapter (1) onto the drive shaft of the tubular drive. You can see which
way to insert the safety catch (2) from its shape. When inserting the drive adapter
safety catch (2) into the hole (4), make sure that the locking lug (3) engages. You will
hear a click. Check that the safety catch is securely in position by pulling on the drive
adapter (1).

Assembling the drive adapter with screw connection

Put the drive adapter (1) onto the drive shaft of the tubular drive. For the assembly,
use an M6 x 12 screw (3) with appropriate washer (2) and suitable screw retainer.
Threaded hole (4)

Securing the drive against axial displacement

-10 mm

In order to secure the drive against axial displacement, we recommend screwing the
drive adapter to the tube.

Attention

When drilling into the barrel, never drill near the tubular drive!

9

Содержание L120/11C PS(+)SMI

























Отзывы: