M
2
M
Model: MX-1000(e)
Quick Install Guide
WHAT’S IN THE BOX
SETTING UP THE ROUTER
1 x BEC MX-1000(e) M2M Router
1 x This Quick Install Guide
1 x Mounting Bracket
1 x MiniFIT to DC Jack Power Cable
1 x Vehicle Power Cable
1 x DC Power Adapter 12VDC 1.2A
2 x Wi-Fi Antennas
3G/4G Antennas
Active GPS Antenna
Ethernet (RJ-45) Cable
(Optional Accessories)
1
Insert the SIM Card
Note: Power off the MX-1000(e) before inserting/removing the SIM
WIFI
WIFI ON/OFF
RESET
WIFI
MINI
USB2
SIM2
SIM1
MINI
USB1
WIFI
WIFI
WIFI ON/OFF
RESET
WIFI
MINI
USB2
SIM2
SIM1
MINI
USB1
WIFI
R
emove the SIM cover
then insert the SIM card(s)
(2FF) with the mental
contacts (gold plate) facing
up to the SIM slot(s) then
push it all the way in until
you hear the clicking sound. Replace the metal SIM cover
after inserting the SIMs.
2
Attach the Wi-Fi Antennas
WIFI
WIFI ON/OFF
RESET
WIFI
MINI
USB2
SIM2
SIM1
MINI
USB1
WIFI
WAN1
MAIN
WIFI
WIFI
WAN1
MAIN
WIFI
WIFI
Note: Use the plastic red caps to cover unused antenna ports
S
crew the 2 female Wi-Fi
antenna cable connectors
until fully attached to the
Wi-Fi ports on MX-1000(e).
D
o not over-torque the
antenna on the connector.
3
Attach the LTE & GPS Antennas
Note: 1. Use the plastic red caps to cover unused antenna ports
2. GPS and 3G/4G-LTE antenna(s) sold separately
S
crew the male SMA
3G/4G-LTE and/or GPS
antennas tight to the
female connectors.
C
onnect to the MAIN port,
the primary cellular antenna
port to transmit and
receive signal, if decide to
use a single LTE antenna.
D
o not over-torque the antenna on the connector.
WAN1
MAIN
USB1
USB2
1
2
3
4
WAN2
AUX
WAN1
AUX
GPS
WAN2
MAIN
POWER
POWER
INTERNET
Gb ETH
GPS
WAN1
WAN2
WAN1
MAIN
WAN2
MAIN
WAN1
MAIN
WAN2
AUX
WAN1
AUX
GPS
WAN2
MAIN
WAN1
MAIN
WAN2
MAIN
WAN1
MAIN
WAN2
AUX
WAN1
AUX
GPS
WAN2
MAIN
WAN1
MAIN
WAN2
MAIN
WAN1
MAIN
WAN2
AUX
WAN1
AUX
GPS
WAN2
MAIN
6
Access to the MX-1000(e)
A
ccess to the MX-1000(e) Web interface by entering
http://192.168.1.254
in the address bar of the web browser.
Default Login Information
: Username (admin) and Password
(A unique12-digit password can be found on the device label).
T
he
Quick Start Wizard
provides key steps to connect the
MX-1000(e) to the Internet.
MINI
USB2
MINI
USB1
Connect to Mini USB Ports
Note: Software programming tool is required for the Mini USB interface
C
onnect to Mini USB port(s)
for direct connection to the
Cellular module(s) for
management – debug,
change firmware, and
configuration.
4
PIN
1
2
3
4
Ground
Ground
ACC
VCC
Black
Black
White
Red
-
-
Input
10
~
56VDC
Definition
Details
Wire color
4
2
1
3
5
Connect to Power Source
Use the DC Power Adapter
A
ttach the power cable
with 4-pin miniFIT to
DC jack power cable
the MX-1000(e) and plug
in the supplied DC
power adapter.
Use Vehicle Electrical System (Power & Ignition Sensing)
A
ttach the Vehicle power cable to
the MX-1000(e) and connect the
wire leads of the power cable to
vehicle’s electrical system.
B
LACK Wire (PIN 1 & 2):
Ground (GND). Use one
of the BLACK wires for
a neutral or ground
connection
W
HITE Wire (PIN 3): ACC/ON for Ignition Input wire need to be
connecting into vehicle accessory wire.
R
ED Wire (PIN 4): VCC/OFF Voltage wire to the battery.
DC power range from 0V to 56V.
Battery
POWER
GND
Ignition Switch
Fuse
ACC
VCC
POWER
