QUICK START GUIDE
iridium SatDOCK 9555
with built in GPS
Suitable for the Iridium 9555
Portable Satellite Telephone
Beam Communications Pty Ltd
8. Using SatDOCK 9555
• After applying power to AC power adaptor or turning key/Acc on, the
SatDOCK will beep upon power up
• Wait for phone to power up and register
PANEL BUTTONS AND INDICATORS:
6. Options
Tracking & Alert:
Tracking & Alert requires GPS antenna, and setup of the tracking and/or
alerting messages. Please refer to the SDMS Application (SatDOCK
Management System) to enable and configure Tracking & Alert.
External Alert Button:
Connect Normally-CLOSED button, to the
Brown
and
Green
wires (it can be extended for longer runs).
The loop needs to be OPEN (eg. pressing button) for
2 seconds to activate Alert state.
Privacy Handset:
1. The Privacy Handset Kit is ordered separately.
2. Mount the handset cup to the mounting plate.
3. Mount the spacer plate and the mounting
bracket, by using the longer screws provided
with the kit. (Re-installed the RAM arm-bracket
behind these plates).
4. Connect the Privacy Handset 3.5mm plug into
the rear cable jack.
5. Privacy Handset mode is active whenever the
handset is removed from the cup.
Intelligent Handset:
1. Mount the handset cup in a suitable position
2. Connect the Intelligent handset RJ45 connector
into the rear cable jack.
3. Intelligent handset mode is active whenever the
handset is removed from the cup
Earpiece-Jack Mode:
Use a 2.5mm earpiece plugged into the right side of the 9555 handset.
1. During a RJ11 or Bluetooth call, to enable Earpiece-Jack Mode, press
and hold the Mute button for 1.5 seconds. The LED flashes
ORANGE
.
2. To exit Earpiece-Jack Mode and revert to RJ11 or Bluetooth, press
the Mute button once.
www.beamcommunications.com
TEL: +61 3 8588 4500 FAX: +61 3 9560 9055
USRQSG005501
7. Add Bluetooth Device
(optional)
AUDIO:
To configure (pair) to a Bluetooth® headset device:
1. Discovery Mode:
Press and hold for 5 secs
the Bluetooth® button on
the cradle. The LED flashes
BLUE
and
ORANGE
.
2. Hold the Headset device button(s) to enter pairing mode.
3. Once paired, the Bluetooth® LED is
BLUE
(half intensity).
4. Bluetooth® can be turned ON with a
single press
, and OFF by
press for
2 secs
the Bluetooth® button on the cradle.
BUTTON
BUTTON MODE
LED/SOUND
Out of Call (single press):
Select Ringer Tones
LED off.
Preview and select ringer sounds.
Out of Call (1.5 second press)
Auto-Answer Mode:
Subsquent 1.5 second press
exits auto-answer
LED is
GREEN
, single beep.
During In-Call Hands-free,
Privacy/Intelligent handset
or Bluetooth®:
Mute (single press)
LED is
RED
when MUTE.
During In-Call Bluetooth®:
Earpiece-jack
(1.5 seconds press)
Subsequent single press, exits
Earpiece-jack
LED flashes
ORANGE
.
Bluetooth® On
(single press)
Bluetooth® OFF
(1.5 seconds press)
LED is
BLUE
(half intensity) when
Bluetooth® ON and is connected
LED is fast-flashing in
BLUE
when
searching paired device.
LED is slow-flashing
BLUE
when a
connected Bluetooth® device is in use.
Single beep sounds when Bluetooth®
turning OFF.
Discovery Mode
(5 seconds press)
LED flashes
ORANGE
and
BLUE
.
Ringer sounds double (2) beeps.
Clear Bluetooth® Devices
(10 seconds press)
Ringer sounds triple (3) beeps.
Send Tracking Message
(single press)
LED and beep operates according to
the settings in PDMS.
Clear Alert Mode
(7 seconds press)
LED turns
GREEN
re-armed & GPS fix
ready. Single Beep sounds.
If LED is flashing in
GREEN
– No GPS
fix, or no Iridium signal
LED is OFF when Track & Alert is
disabled.
+
Activate Alert Mode
(2 seconds press, BOTH
buttons together)
Track LED turns
RED
when alert is
triggered and single beep sounds.
Track LED is flashing in
RED
when the
alert message is sent.
Track LED is flashing in
ORANGE
when the alert message is
acknowledged by a remote host.
