BE Ag & Industrial AGRI EASE BE-LS22TL6505GC Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 40

BE Ag & Industrial AGRI EASE BE-LS22TL6505GC Скачать руководство пользователя страница 29

Page 22

The control handle has three positions.

See FIGURE 21.

•

FORWARD

— To split wood. Move the control handle to the FORWARD position to move wedge toward the log to split.

NOTE:

The control handle will return to the NEUTRAL position as soon as the handle is released (FORWARD

position only), and the wedge stops moving forward.

• NEUTRAL

— To stop wedge. Release the control handle or move the lever to the NEUTRAL position to stop the wedge

movement.

• REVERSE

— To return the wedge. Move the control handle to the REVERSE position, the wedge returns automatically

toward the cylinder. When the wedge is fully retracted, the control handle returns to the NEUTRAL position automatically.

Do not hold the handle in the REVERSE position when fully retracted.

NOTE:

The REVERSE position may also be moved back to the NEUTRAL position manually, if necessary.

WARNING!

If the control handle on your log splitter is not functioning properly, STOP USE IMMEDIATELY

and contact an authorized service dealer.

WARNING!

Do not attempt to service, repair or replace control valve. Contact an authorized service dealer.

WARNING!

Do not attempt to adjust or modify the control valve or the hydraulic system from its original

settings or manufacturer in any way.

USING CONTROL HANDLE

OPERATION INSTRUCTIONS

(FIGURE

21)

Neutral

Reverse

Forward

Page 25

«
...
27
28
29
30
31
...
»

Содержание AGRI EASE BE-LS22TL6505GC









































Отзывы:

Нет отзывов