7
3
1
2
5
6
4
8
9
10
8
11
9
7
3
Crotch height
1”
Horizontal top tube height
Training Bike
Please retain this leaflet for reference to the manufacturer.
IMPORTANT
Please contact our helpline on customer service number
01253 775570 for any enquires.
Save all packaging material until assembly is completed.
PLEASE READ BEFORE ASSEMBLY
CONTENTS:
1
Main frame with rear wheel
2 Front fork with front wheel
3
Plastic ring
4
Saddle
5
Handlebars
6
Clamp cover
7 Metal clamp
8 8mm x 38mm Screw (2)
9 8mm Washer (2)
10 8mm Dome nut
11 8mm Nylock nut
Multi-spanner included
IMPORTANT OWNER’S INFORMATION
Please read this before allowing your child to ride the bicycle.
CORRECT BICYCLE SIZE
Make sure the bicycle you have bought is the correct size for the child.
The minimum crotch measurement of the rider, with feet flat on the
ground, should be 1” (25mm) more than the height of the horizontal
top tube line, shown below.
BICYCLE SET-UP
It is essential that, before moving off, the rider is comfortably
seated on the bicycle and not stretching forward to reach the
handlebars.
Re-check the instructions given for the installation of the saddle.
FOR YOUR CHILD’S SAFETY
Recheck that all screws, nuts and bolts are firmly tightened.
Make sure that your child is capable of riding this bicycle.
Do not allow your child to ride without supervision.
Young children should only ride under constant supervision.
This bicycle is to be assembled by an adult.
Check all parts & fixtures are secure before allowing a child to ride this bike.
Not for children with a body weight of more than 20 kgs.
Warning! A protective helmet should be worn when cycling!
FITTING THE HANDLEBARS
1 Remove protective cap and slide the clamp cover
onto the handlebar stem.
2 Push the handlebar stem into the fork stem at least as
far as the Minimum insertion mark.
3 Align the handlebar with the front wheel and tighten
the clamp with the spanner.
4 Slide the clamp cover
down over the clamp.
FRONT FORK ASSEMBLY
1 Remove protective cap and slide the fork stem through
the front head tube.
2 Push the plastic ring and clamp onto the top of
the fork stem.
FITTING THE SADDLE
1 Push the saddle pillar into the down tube at least as far
as the Minimum insertion mark.
2 Align the saddle with the bike frame and tighten the clamp
with a spanner.
A GUIDE TO SAFE CYCLING
1. We recommend this bike is for pavement use only. Not suitable for use on public highways.
2. Do not ride at night. Visibility is often limited at dawn and dusk.
3. Always give pedestrians right-of-way, and don’t ride to close to them. Never park your bicycle
where it can cause a nuisance.
4. Avoid hazards that may cause you to lose control of your bicycle such as pot holes, uneven
pavements and manhole covers.
5. Leave plenty of room when passing parked vehicles and watch out for doors being opened
in your path.
6. Never carry passengers on your bicycle. Never carry packages in your hands while riding,
or fix anything to your bicycle that could obstruct your visibility or control.
7. Don't wear anything that restricts your hearing.
8. Always ride with both hands on the handlebars.
9. Don’t wear very loose clothing, which could hang down and become caught in the wheels of
your bicycle. Wear cuff bands or trouser clips to keep your trousers from getting caught in the
wheel.
10. We recommend that light-coloured or fluorescent clothing be worn which helps others to see
you in daylight and poor light.
11. Always wear proper safety equipment. We recommend a helmet, long-sleeve shirt, long trousers,
shoes and elbow and knee pads. Gloves and eye protection also make good sense.
Cover your handlebars, stem and top tube with safety pads for extra protection.
PLEASE REFER TO THE HIGHWAY CODE REGARDING RULES FOR CYCLISTS.
ASSEMBLED BIKE
Please check all screws and fittings are secure before
giving to your child. The toy should be used with caution,
since it requires great skill, so as to avoid falls or
collisions causing injury to the user and third parties.
RECOMMENDED TORQUE TOLERANCES
Handlebar clamp 20 nm
Seat Post 20 nm
Wheels 20 nm
Minimum
insertion
mark
Minimum
insertion mark
1
2
3
5
4
6
7
8
9
10
11
2
+
HTI Group, FY7 7NY
