background image

User Manual 

7  

2006/42/EEC 

Machinery Directive

2006/95/EEC 

Low Voltage Directive 

2004/108/EEC 

Electromagnetic Compatibility Directive (EMC)

2011/65/EU

 Restrictions on the use of hazardous substances in electrical and elec-

tronic equipment (RoHS)

The Sigmax R19 printer has been manufactured in compliance with the following harmonised standards, and con-
sequently  conforms to the essential requirements established by the Directives:

2006/42/EEC

 UNE-EN ISO 12100:2012; UNE-EN ISO13732-1 :2008; EN ISO 7010:2012

2006/95/EEC

 UNE-EN 60204-1;UNE-EN 60947-3:2009

2004/108/EEC

 UNE-EN 55022:2011; UNE-EN 55024:2011; UNE-EN 61000-4-3-2:2007

Changes / modifications not approved by the responsible party could void the user’s authority to operate the 
equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a 
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed 
and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does 
cause harmful interference to radio or television reception, which can be determined by turning the equipment off 
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
•  Reorient or relocate the receiving antenna.
•  Increase the separation between the equipment and receiver.
•  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•  Consult the dealer or an experienced radio/TV technician for help.

The CIM Private Foundation Centre declares that the Sigmax R19 printer complies with the essential requirements 
and any other applicable or mandatory provisions of the Directives. 

It complies with the essential requirements of the European Directives:

Conformity

Fundació Privada Centre CIM 
Llorens i Artigas, 12 08028 Barcelona. 
Tel: +34 934017171

 www.fundaciocim.org

REI-RAEE: 6107

Содержание Sigmax R19





























































Отзывы: