WARNING: Electrostatic Sensitive Device (ESD)
Static electricity can easily damage your motherboard and will void your motherboard warranty. Keep the motherboard
and other system components in their anti-static packaging until you are ready to install them. Touch a grounded surface
before you remove any system component from its protective anti-static packaging. Unpacking and installation should be
done on a grounded, anti-static mat. The operator should be wearing an anti-static wristband, grounded at the same
points as the anti-static mat. During configuration and installation touch a grounded surface frequently to discharge any
static electrical charge that may have built up in your body. Avoid touching the components when handling the
motherboard or a peripheral card. Handle the motherboard and peripheral cards either by the edges or by the peripheral
card case-mounting bracket.
WARNING: Misplaced Jumper Damage
Incorrect jumpers and connectors settings may lead to damage to your motherboard and will void your motherboard
warranty. Please pay special attention to not connect these headers in the wrong direction. DO NOT change ANY jumpers
while the motherboard has power.
Jumper / Connector
Name
Description
Note
CI1
Chassis Intrusion Pinheader
2 pin
CLR_CMOS1
Clear CMOS Jumper
3 pin
COM2-5
Serial Port Connector
2x5 pin (keyed)
JCOMP2-5
COM Power Jumper
3 pin
CPUFAN1
Fan Power Connector
4 pin
SYSFAN1-2
Fan Power Connector
4 pin
JAMP1
Audio Amplifier Pinheader
4 pin
JAUD1
Front Audio
2x5 pin (keyed)
JAT1
ATX/AT Jumper
3 pin
JFP1
Front Panel Pinheader
2x5 pin (keyed)
JGPIO1
GPIO Pinheader
2x5 pin
JINV1
LVDS Inverter Connector
5 pin
JLVDS1
LVDS Connector
2x20 pin
JVDD1
LVDS Power Jumper
3 pin
JLPT1
Parallel Port Pinheader
2x13 pin (keyed)
JSPDI1
S/PDIF Pinheader
3 pin
SATA cables
User’s Quick Start Card
Version 1.0
http://www.bcmcom.com
Package Contents:
One
RX77Q Motherboard
One
2 COM Ports with Bracket
Two
SATA cables
One
Standard I/O Shield
One
Driver CD/DVD
One
User’s Quick Start Card
Disclaimer:
This manual is provided “As-Is” with no warranties of any kind, expressed or implied, including, but not limited to the
implied warranties or conditions of this product’s fitness for any particular purpose. In no event shall we be liable for any
loss of profits, loss of business, loss of data, interruption of business, or indirect, special, incidental, or consequential
damages of any kind, even the possibility of such damages arising from any defect or error in this manual or product. We
reserve the right to modify and update the user manual without prior notice.
WARNING: CMOS Battery Damage
Replace your system’s CMOS RAM battery only with the identical CR-2032 3V Lithium-Ion coin cell (or equivalent) battery
type to avoid risk of personal injury or physical damage to your equipment. Improper installation might cause battery to
explode. Always dispose of used batteries according to the manufacturer’s instructions, or as required by the local
ordinance (where applicable). The damage due to not following this warning will void your motherboard’s manufacturer
warranty.
Perchlorate Material- Special Handling May Apply.
See
http://www.dtsc.ca.gov/hazardouswaste/perchlorate/
Additional Information:
Additional information on setting this board up can be found in the User’s Manual in the provided CD or DVD ROM. The
Online User’s Manual and FAQ/Knowledge Base can be found on our website by visiting our website:
http://www.bcmcom.com
. If your question is not answered in our FAQ/Knowledge Base, visit our forums and post your
messages or submit a new FAQ through FAQ Submittal form for us to add your question in our FAQ with our answer.
ATTENTION: Incorrect BIOS Setup
If you do not know how to handle BIOS setup or how to set it up properly, it is strongly advisable that you do not modify
any of the settings than otherwise instructed in the User’s Quick Start Card. Even a seemingly small incorrect adjustment
or modification in the BIOS setup can render your system unstable or unusable. Incorrect BIOS setup is not covered by
your motherboard’s manufacturer warranty. Try to Clear CMOS when system does not boot after BIOS settings change.
I/O Shield
Driver CD/DVD
COM Ports w/ Bracket
RX77Q
Содержание RX77Q
Страница 3: ......
