BCE FlexStation Venus Overhead, Инструкция по сборке

Страница: 1 / 4

WZ-CrnrOverhead
Note:
Note:
Determine if cabinet to be installed is
to be right-hand or left. This instruction
covers right, though left-hand cabinet
installation is similar, it will have a different
set of overhead stanchions.
WorkZone Corner Desk must be fully
installed prior to installing the overhead unit.
1. Begin by removing grommet covers at
the rear corner, and side location where the
overhead cabinet will be installed (Figure 1).
2. At the rear corner, from underneath the
corner worksurface, install a corner
overhead mounting tube using two #12 x
1-3/4” screws (Figure 1).
3. Position the corner stanchion (left-hand)
as illustrated through the corner grommet
hole, aligning the mounting holes in the
bracket of the stanchion with the mounting
holes of the corner overhead mounting tube.
Secure bracket to tube using two #10-32 x
1/2” screws (Figure1).
4. Position the right-hand stanchion with the
bracket through the grommet hole, aligning
the mounting holes in the bracket of the
stanchion with the mounting holes in the top
of the right-hand leg. Secure bracket to leg
using two #10-32 x 1/2” screws (Figure1).
5. Carefully set the Balance Overhead
Cabinet onto the two installed stanchions.
Align the three sets of mounting holes on
each side of cabinet/stanchion and secure
using three #10 x 3/4” screws each side
(Figure 1).
6. Remove the knock-outs from the
grommet covers removed in step 1, and
snap them back into place in the grommet
holes at the stanchions (Figure 2).
WorkZone Corner Desk with Balance Overhead Cabinet
grommet
covers
grommet
knock-out
grommet
knock-out
Venus
overhead cabinet
corner
stanchion
corner overhead
mounting tube
#12 x 1 / ”
screw
3
4
right-hand
stanchion
#10-32 x ½”
screw
#10 x / ”
screw
3
4
#10-32 x 1”
screw
Figure1
Note: Determine if cabinet to be
installed is to be right-hand or left.
This instruction covers right, though
left-hand cabinet installation is similar,
it will have a different set of overhead
stanchions.
Note:
FlexStation Corner Desk must be
fully assembled prior to installing the
overhead unit.
1. Begin by removing grommet covers
at the rear corner, and side location
where the overhead cabinet will be
installed (Figure 1).
2. At the rear corner, from underneath
the corner worksurface, install a
corner overhead mounting tube
using two #12 x 1
3
/
4
” screws
(Figure 1).
3. Position the corner stanchion (left-
hand) as illustrated through the
corner grommet hole, aligning the
mounting holes in the bracket of the
stanchion with the mounting holes
of the corner overhead mounting
tube. Secure bracket to tube using
two #10-32 x
1
/
2
” screws (Figure 1).
4. Position the right-hand stanchion
with the bracket through the
grommet hole, aligning the
mounting holes in the bracket of
the stanchion with the mounting
holes in the top of the right-hand
leg. Secure bracket to leg using two
#10-32 x
1
/
2
” screws (Figure 1).
5. Carefully set the Venus Overhead
Cabinet onto the two installed
stanchions. Align the three sets of
mounting holes on each side of
cabinet/stanchion and secure using
three #10 x
3
/
4
” screws each side
(Figure 1).
6. Remove the knock-outs from
the grommet covers removed in
step 1, and snap them back into
place in the grommet holes at the
stanchions (Figure 2).
Assembly Instructions
FlexStation Corner Desk Overhead Cabinet
Venus Overhead
OE-60931/PDF0314
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.