1
175
80
72.5
175
80
72.5
5928442
ProAccess
LED
Vehicle detection sensor for gates and barriers
Original operating instructions
General
1
Safety instructions
ENGLISH
399452E
03/21
Sensor unit
Control unit
Control
Unit
Mode indicator
Button: VALUE
selection
Value indicator
Button:
Area Check
Button: PARAMERTER
selection
Button:
Microwave Range
Button: Output logic
Button:
Sensor Mode
Button:
Calibration
Dimensions
Sensor
Unit
(Further details see chapter 3)
• Read these operating instructions thoroughly before putting the device into
operation and keep them for future reference.
• This product is a vehicle detection sensor designed to detect approach and
presence of a vehicle in proximity of a gate or barrier.
• Do not use this product other than for its specified application.
• The assembly, commissioning, modifications and extensions may only be
completed by an experienced electrician!
• Pay attention to all local relevant electrical safety regulations!
• Failure to follow these safety precautions may cause damage to sensor or
objects, serious personal injury, or death.
• It is the responsibility of the equipment installer to carry out a risk assessment
and to install the system, in compliance with applicable local, national and
international regulations, safety standards, codes and laws as well as the
Machinery Directive 2006/42/EC, should this apply.
• Observe all applicable local, national, and international door safety standards,
codes, and laws.
• Always consider the safety functions of your applications as a whole, never
just in relation to one individual section of the system.
• The installer is responsible for testing the system to ensure it meets all
applicable safety standards.
• During the operation of electrical components – e. g. in the case of a short
circuit hot and ionised gases can be emitted; protection covers must not be
removed!
• The device should only be operated from a safety extra low voltage (SELV)
system with safe electrical separation according to EN 61558. The wiring must
be protected against mechanical damage.
Prior to starting installation or mounting, take the following safety precautions:
• Check the voltage data on the label of the sensor.
• Ensure that the device/installations cannot be switched on!
• Ensure that the power supply is disconnected!
• Protect the device with a housing against contamination or harsh environ-
ments!
• Protect the sensor against rain and snow.
• Disconnect device from mains in the event of a fault.
• Avoid touching any electronic and optical components.
• The door drive and the transom must be properly earthed.
• After accessing the inside of the device, ensure the cover/protection seal is
closed tightly to achieve designated protection rating.
• Ensure the commercial door operator has all of its monitored entrapment
protection devices installed and operational. This sensor does not replace any
entrapment protection devices.
• Limited protection against accidental contact!
• Read these operating instructions thoroughly before putting the device into
operation and keep them for future reference.
• This product is a vehicle detection sensor designed to detect approach and
presence of a vehicle in proximity of a gate or barrier.
• Do not use this product other than for its specified application.
• The assembly, commissioning, modifications and extensions may only be
completed by an experienced electrician!
• Pay attention to all local relevant electrical safety regulations!
• Failure to follow these safety precautions may cause damage to sensor or
objects, serious personal injury, or death.
• It is the responsibility of the equipment installer to carry out a risk assessment
and to install the system, in compliance with applicable local, national and
international regulations, safety standards, codes and laws as well as the
Machinery Directive 2006/42/EC, should this apply.
• Observe all applicable local, national, and international door safety standards,
codes, and laws.
• Always consider the safety functions of your applications as a whole, never
just in relation to one individual section of the system.
• The installer is responsible for testing the system to ensure it meets all
applicable safety standards.
• During the operation of electrical components – e. g. in the case of a short
circuit hot and ionised gases can be emitted; protection covers must not be
removed!
• The device should only be operated from a safety extra low voltage (SELV)
system with safe electrical separation according to EN 61558. The wiring must
be protected against mechanical damage.
Prior to starting installation or mounting, take the following safety precautions:
• Check the voltage data on the label of the sensor.
• Ensure that the device/installations cannot be switched on!
• Ensure that the power supply is disconnected!
• Protect the device with a housing against contamination or harsh environ-
ments!
• Protect the sensor against rain and snow.
• Disconnect device from mains in the event of a fault.
• Avoid touching any electronic and optical components.
• The door drive and the transom must be properly earthed.
• After accessing the inside of the device, ensure the cover/protection seal is
closed tightly to achieve designated protection rating.
• Ensure the commercial door operator has all of its monitored entrapment
protection devices installed and operational. This sensor does not replace any
entrapment protection devices.
• Limited protection against accidental contact!