manualshive.com logo in svg

Bay Networks Remote Annex 2000, Руководство по установке оборудования, Страница: 58 / 136

Поделиться
Скачать
Bay Networks Remote Annex 2000 Скачать руководство пользователя страница 58

Remote Annex 2000 Hardware Installation Guide

Chapter 2    Installing the Remote Annex 2000

2-24

The host serving the Remote Annex 2000 its boot information must
be running on the same network as the Remote Annex 2000 because
the Remote Annex 2000 only broadcasts BOOTP and RARP queries.

If BOOTP and RARP fail, the Remote Annex 2000 transmits an IPX
Advertisement Request for Service and a MOP Multicast boot request.

If all requests fail, the Remote Annex 2000 returns to the ROM monitor
(if in Test mode) or continues the auto-initializing procedure
indefinately (if in normal mode).

Self-booting the Remote Annex 2000

If you purchased a Remote Annex 2000 with Flash ROM, your device
already contains an operational image. You can check your Remote
Annex 2000’s configuration by entering the config command at the
ROM Monitor prompt. The config command displays the current
configuration information and revision levels. If your device has Flash
ROM installed, the line FLASH PROM size: appears under the
REVISION/CONFIGURATION INFORMATION section.

This section contains a description of what you need to do to boot
your Remote Annex 2000 from Flash ROM. Proceed as follows:

1

Enter the ROM Monitor prompt from the Console.

2

Set the Internet address to a valid IP address and the subnet mask to
a valid mask using the

addr

command.

3

Set the interface sequence to

self

 using the

sequence

 command.

4

Boot the Remote Annex.

Содержание Remote Annex 2000









































































































































Отзывы:

Нет отзывов