manualshive.com logo in svg

baxter Flo-Gard 6301, Руководство по обслуживанию, Страница: 18 / 252

Поделиться
Скачать
baxter Flo-Gard 6301 Скачать руководство пользователя страница 18

1

Warranty Information

1-4

FLO-GARD 6301 DUAL CHANNEL VOLUMETRIC INFUSION PUMP SERVICE MANUAL

07-19-B1-729

Warranty Information

Baxter Healthcare Corporation (“Baxter”) warrants that the equipment shall 
be free from defects in material and workmanship when delivered to the 
original purchaser. Baxter’s sole obligation shall be limited to repair or 
replacement, at Baxter’s option and expense, of the defective part or unit, 
excluding batteries, for a period of one year following the date of initial 
delivery. The warranty for batteries is limited to a period of six months 
following the date of initial delivery.

The warranty extends only to the original purchaser and is not assignable or 
transferable, and shall not apply to auxiliary equipment or disposable 
accessories.

THERE ARE NO OTHER WARRANTIES INCLUDING ANY IMPLIED 
WARRANTY AND ANY WARRANTY OF MERCHANTABILITY OR 
FITNESS FOR A PARTICULAR PURPOSE WHICH EXTEND BEYOND 
THE DESCRIPTION OF THE PRODUCT AND THOSE EXPRESSLY SET 
FORTH IN ITS LABELING. UNLESS USED ACCORDING TO THE 
DIRECTIONS ACCOMPANYING THE PRODUCT, ALL WARRANTIES 
ARE SPECIFICALLY EXCLUDED. In no event shall Baxter be responsible 
for incidental, consequential or exemplary damages. Modification, alteration, 
recalibration, abuse, or service by other than a Baxter authorized 
representative may void this warranty.

Service Information

While under Baxter Healthcare Corporation Warranty, Service Agreement 
(optional), or lease agreement, the instrument must not be opened by 
unauthorized personnel.

Call 1-(800) -THE-PUMP for service and repair information for all 
instruments.

CAUTION

Where connectors are identified as “locking,” unlock the connectors before 
removing cables or conductors.

CAUTION

Note the routing of the wires before removing them.

CAUTION

Fully unlock flat ribbon cable connector flange before removing cable. 
Attempting to remove the cable while locked can damage the cable and 
connector.

CAUTION

Ensure that the door assemblies are properly latched prior to transport or 
storage.

Содержание Flo-Gard 6301





























































































































































































































































Отзывы:

Нет отзывов