BAVONO PTM-937WDR
Outdoor 37X Zoom Wide Dynamic Range PTZ Dome Camera
I. Performance Instruction
Chapter One — Product Overview
II. Feature Functions Instruction
I. Wiring of Dome System
Chapter Two — Wiring and Setup of Dome System
Basic system connection
In the drawing, JMP-120R is
the impedance matching
selection of control signal and
noise restrain of RS-485, when
there is long distance
transmission or noise-control,
it can short jumper
User Manual
Address of Dome device is from 0 - 255.The number (address) of dome device in the control system is setup by
the hardware (8-digit on and off switch) of dome device.
Integrate multi-protocol and auto protocol differentiation. Note: The dome device only auto differentiate
controller of the first communication.
Pan 360 degree continuous rotation.
Tilt 90 degree action plus 2 degree angle adjustment. Plus the 2 degree adjustment, the view angle can be 90 or
92 degree.
Pan manual operation speed can be 0.1 to 300 degree per second
Tilt manual operation speed can be 0.1 to 120 degree per second
128 preshot positions (A fixed position that aimed by the dome camera, which can be set and revised by user
arbitrarily)
The maximum running speed when preshot is being called can reach 400 degree per second with accuracy of
±0.1 degree.
Compatible with many kinds of Module Camera
Power supply : AC 24V 1A (indoor type), AC 24V 2A (outdoor type)
Easy installation interface.
Pass environmental protection grade IP66 (outdoor type)
Adopts long distance RS-485 transmission mode
Transmission speed, i.e, Baud rate is selectable (Set by the fifth and sixth bit of the on and off switch of the dome
device, baud rate 2400bps - 19200bps)
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
Multi-language operation menu and function display.
Camera name and operation position and angle display (The name of the camera can be edited and the
coordinate angle of the dome device can be displayed on the screen)
Operation crosshair function (Enable this option, the target can be captured more effectively with crosshair on
the screen)
Three PTZ tours operation with 2 minutes record of each tour (Can real-time monitor and record the action of
manual operation)
Six group of programmable vector scans (including scan speed, dwell time, preshot and interruption between
tours)
Auto flip function with 10 degree move up
Eight sectors of programmable sectional mask (Can mask part of the sectors of camera , which differs depending
on different types of camera)
Eight sectors of programmable sectional display (Can display the name and nature of concrete position
shooting by the camera, which differs depending on different types of camera)
Auto enter function running after self-test of the dome device and auto enter function running when there is no
transmission (Dwell time can be set form 1 to 999 seconds)
Frozen video picture function (freez picture function)
Operation return function (after executing operation return, the dome device will return to the previous
operation)
Intelligent manual scan function (execute this function in manual pan operation, you can adjust the manual pan
operation)
Intelligent power off real time memory (If power was cut off when a certain function is in operation, the dome
device can resume working at where the power is cut off )
High efficient 3-dimension scan
Camera zoom in speed limit function. ( When it was zooming in, the speed of the dome device will auto slow
down )
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
1.
Multi-dome device connection
When connecting many dome
devices together, the user can
embed multi-device system with
auxiliaries such as arrester
device, video matrix , DVR and
alarm box for system integration.
AV24V: Power supply of dome
device, which will convert 110V /
60Hz or 220V/50Hz input to AC
24V output and supply to the
dome device.
2.
Attention: No operation when
the dome device is power on!
II. Setting of Dome Device Communication
Before installation and use, the setting of communication protocol and transmission speed (baud rate ) should comply with
the control system
Wiring (Please do not turn the power on)
1.
Setting dome device address. (Turn the power off when setting, and restart the device after revision)
3.
4.
5.
6.
2.
Install camera. (Please refer to camera installation for details)
Attention: 1. Do not connect the camera and dome device with FFC in a wrong way.
2. The installation holes of different camera differ.
Connect the power of dome device
At this moment, the self-test (rotation) of dome device and self-test ( there will be image on the monitor) of camera can be seen.
Attention: When the dome device is self-testing, it is normal when sound is issued caused by the block of dome device after 2 - 5
seconds of vertical movement, which is the orientation of the dome itself.
Controller setting
Set the protocol, baud rate and address of the keyboard controller identical with those of dome device. (Please refer to keyboard
controller instruction manual).
Attention: If the setting of protocol of dome device is auto detection, the protocol of keyboard controller can be set arbitrarily,
But its baud rate should be set identical with that of the dome device.
7. Start testing.
When all the above are ready, the testing to dome device can be started.
( Please refer to the next section for demonstration of menu operation and control of dome device.)
The figure shows: Address of the dome device: No.1
(Please refer to detailed parameter in next chapter)
This dip switch located on PCB in the dome device
8. Complete the test (Summary)
1) If the performance of item 7 is normal, it indicates the system is basically normal, Please do not change the wiring
and various setting to avoid fault and unnecessary damage and loss.
2) If the performance of item 7 is abnormal, or only one item works normally, please check the wiring ( item 1 and 4 ) and
setting (item 2 ,3 and 6 ) carefully.
Chapter Three — English Operation Menu of Dome Device
I. Main menu
1.
2.
3.
Press 95+SHOT on the keyboard to enter the Main menu of dome
device
Select options joy stick only between up and down, the arrow
points to the current selected option, Press OPEN or left right of
joystick to command entering the submenu ofthat option or
change the value or setting of that option.
Press CLOSE to exit menu or return to upper stage menu
• RS-485 Bus: It is for the control signal (RS-485 signal ) output of controller, connecting to the communication
input terminals of control cable of each dome device.
• Video: It is for image signal output of dome device, (Can directly output to video equipment such as monitor
or video matrix. Take care of the match up of impedance)
Setting protocol and baud rate (Turn the power off when setting,
and restart the device after revision).
2. Sector Setup
Sector setup Press OPEN or joystick left or right to enter
3. Control Options
Control options Press OPEN or joystick left or right to enter
4. Diagnostic Options
Diagnostic options Press OPEN or joystick left or right to enter
Joystick left or right when programming to select preshot and press OPEN
to confirm.
Joystick left or right to select (0 - 9 or A - Z). Press OPEN to confirm selection.
Press CLOSE to exit or return to upper stage menu when programming is
done
< Setup pan start point. Press OPEN or joystick left or right to enter Capture
the start point and press CLOSE to exit and return to upper stage menu.
< Edit the name of preshot. Press OPEN or joystick left or right enter
< Joystick left or right when programming to select preshot and press
OPEN to confirm
< Name display On / Off joystick left or right select IRIS CLOSE to Exit
⑤
Name
⑥
Name Display
Joystick left or right to select (0 - 9 or A - Z). Press OPEN to confirm
selection, Press CLOSE to exit or return to upper stage menu when
programming is done.
1). Number ( 1 - 9 ) Number selection joystick left or right to select
2). Name editing Press OPEN or joystick left or right to entere
3). Pan Start pos
< Setup pan end point, Press OPEN or joystick left or right to enter. Capture the
end point and press CLOSE to exit and return to upper stage menu.
4). Pan End pos
< Setup tilt start point, Press OPEN or joystick left or right to enter, Capture the
start point and press CLOSE to exit return to upper stage menu.
5). Tilt Start pos
< Setup tile end point. Press OPEN or joystick left or right to enter. Capture the
end point and press CLOSE to exit and return to upper menu.
6). Tilt End pos
< Sector name display ON/OFF joystick left or right to select
< Coordinates display ON/OFF joystick left or right to select
< Crosshairs ON/OFF joystick left or right to select
< Start-up screen message display ON/OFF Joystick left or right to select
< Pan/Tilt setup of dome device Press OPEN or joystick left or right to enter
7). Name display ON/OFF
8). Coordinates ON/OFF
9). Crosshairs ON/OFF
10). Start-UP scr messsage ON/OFF
1). Set pan and Tilt
2). Set Default Function
3). Delay
4). Operation ON/OFF
<Set default function Press OPEN or joystick or right to enter
< Default function ON/OFF joystick left or right to select IRIS CLOSE Exit Speed Limit ON/OFF
< Operation speed limit ON/OFF joystick left or right to select Auto Flip ON/OFF
< Auto flip ON/OFF joystick left or right to select Auto Focus PTZ/OFF/Z
< Auto focus options joystick left or right to select Auto AE PTZ/OFF/Z
< Auto AE option joystick left or right to select Vector scan AF ON/OFF
< Vector scan auto focus control joystick left or right to select IRIS CLOSE to Exit
< Time delay setting (second) Press OPEN or joystick left or right to enter
< Joystick left or right when programming to select preshot and press OPEN to
confirm
①
Pan Reverse ON/OFF < Pan Reverse ON/OFF joystick left or right to select
②
Tilt Reverse ON/OFF < Tilt Reverse ON/OFF joystick left or right to select
③
+2 Tilt Limit ON/OFF <+2 Tilt Limit ON/OFF joystick left or right to select
④
Find Home on STA ON/OFF < Find Home on start ON/OFF joystick left or right to select
IRIS CLOSE to Exit
①
Default Function P/V/T
②
Number 1
< Select default function (Preshot /Tour /PTZ) Press OPEN or joystick left or right to enter
< Function number selection Press OPEN or joystick left or right to enter
< Joystick left or right when programming to select preshot and press OPEN to
confirm
<
Joystick left or right to select (0 - 9),Press OPEN to confirm selection.
Press CLOSE to exit or return to upper stage menu when programming is done
Joystick left or right to select (0 - 9). Press OPEN to confirm selection.
Press CLOSE to exit or return to upper stage menu when programming is done
1). Clear Memory
< Clear data in the memory
Press OPEN or joystick left or right to enter
< Reminder:are you sure to do this
Press OPEN to confirm
Press CLOSE to exit and return to upper stage menu
2). Restore Def Setting
3) Color system PAL/NTSC
4). Scan & Camera Reset (Null)
5). Dome Information
< PAL/NTSC switch joystick left or right to select
< Restart dome camera. Press OPEN or joystick left or right to enter
< Restore default setting
Press OPEN or joystick left or right to enter
< Reminder: are you sure to do this
Press OPEN to confirm
Press CLOSE to exit and return to upper stage menu
Dome information, Press OPEN or joystick left or right to enter
Type of camera
Control protocol
Baud rate
Dome number
Press CLOSE to exit and return to upper stage menu
IRIS CLOSE to Exit
<
<
<
<
<
<
5. Camera Options
WDR/BLC Setting
1. Press [EXIT]
2. Use [up] or [down] button to select the [EXIT] then use [left] or [right] button to select a
mode
• RET: Return to the previous.
• TOP: Return to the CAMERA SETTING menu screen.
• END: Exit the setup menu.
Note: The setup menu will be disappear after save the current setting value.
The MENU screen appears on the monitor.
Check the current settings on the menu.
• You can use the camera identification (CAMERA ID) to assign a number to the camera.
• You can set the exposure options using the EXPOSURE menu.
• Use WDR/BLC option to set the options
for BLC or WDR camera.
Select [EXPOSURE] option on the [CAMERA SETTING] menu.
Press [EXIT] button and the EXPOSURE menu appears.
• You can set the brightness level. (0-100)
1. Select [BRIGHTNESS] option.
2. Use [left] or [right] button to set the bright level.
• AGC (Automatic Gain Control) setting
• If pictures are not clear due to darkness, use for increase the sensitivity of picture.
If the images are too dark, change the maximum [AGC] value to make the images lighter.
1. Select [WDR/BLC] option.
2. Use [left] or [right] button to select a mode then press [EXIT].
1. Select [CAMERA ID] option on the [CAMERA SETTING] menu.
2. Use [left] or [right] to select a CAMERA ID (OFF, 1-255).
• WDR: Set the WDR limit. - WDR LIMIT: LOW
←→
MIDDLE
←→
HIGH
• BLC: Set the BLC limit. - BLC LIMIT: LOW
←→
MIDDLE
←→
HIGH
• HSBLC: Use for adjusting brightness the specific area of picture.
- AREA SETTING: Use [left] or [right] button to select a area then use [up]or [down]
button to select a ON or OFF. Press [EXIT] to exit the Area setting menu.
- GRAY SCALE: Use [left] or [right] button to select a gray scale.
(GRAY
←→
D.GRAY
←→
BLACK).
- USER SCALE: Use [left] or [right] button to select a bright level.(5 level)
1. Select [AGC] option.
2. Use [left] or [right] button to select a mode.
(OFF
←→
LOW
←→
MIDDLE
←→
HIGH)
1. Use [up] or [down] button to select [SENS-UP] option.
2. Use [left] or [right] button to select a [AUTO].To setting the [AUTO] funtion, select the
[AUTO] on the [SHUTTER].
3. Press and use [left] or [right] button to set the SENS-UP limit (x2~x128).
Note: If you set to one of the SHUTTER options except AUTO on the
[SHUTTER] menu, the [SENS-UP] setting is not available and [---] mark is displayed.
• ATW (Auto-Tracing White Balance): The color temperature
range for the proper white balance is approximately 1700 - 11000K. Proper white
balance may not be obtained under the following conditions:
• You can select one of three modes for white balance adjustment.
1. Select [WHITE BAL] option.
2. Use [left] or [right] button to select one of three modes for white balance then press
[EXIT].
1) The color temperature is out of the 1700 - 11000K range.
2) When the scene contains mostly high color temperature objects, such as a blue
sky or sunset.
3) When the scene is dim.
• AWC
→
PUSH: If you select the AWC
→
PUSH mode, you will be able to set up
the White Balance automatically using [EXIT] button.
• MANUAL: You can set the white balance options manually.
- COLOR TEMP: Use [left] or [right] button to select a funtion.
(INDOOR: 3200, OUTDOOR: 5100)
- RED: Obtains the optimum amount of red gain.
- BLUE: Obtains the optimum amount of blue gain.It is a function of a color camera to delete
the filter with the IR Cut function in an illumination below the standard value so that it has
a better sensitivity.
II.Tree Menu List
1. All sub-menus can be seen clearly in this tree list.
1
）
Language Options
< Language options joystick left or right to select
< Display options
< Preshot setup options
< Preshot number selection Press OPEN or joy stick left or right enter
< The default number after entering is 001, (hundred bit / ten bit / single bit),
joy stick left or right to select preshot position and press OPEN to confirm ,
and joy stick left or right again to select numbers(0 - 9), Press OPEN to confirm
the selection.
①
Preshot (Preset position) Setup
< Select preshot and press CLOSE to confirm the programming when done
and auto exit and return to the upper stage menu.
②
Set Preshot
< The action of the dome device can be seen and return to
corresponding preshot point.
③
Call Preshot
< Press OPEN or joystick left or right to enter
< Reminder: Are you sure to delete preshot?
④
Delete Preshot
Press OPEN to confirm
Press CLOSE to exit and return to upper stage menu
IRIS CLOSE to Exit
IRIS CLOSE to Exit
01
02
03
04
05
06
07
08
To Open and Exit the Menu screen
Camera Identification Setting
Exposure Setting
Brightness setting
SENS-UP setting
Setting the WB (White Balance) Mode
White Balance Setting
