manualshive.com logo in svg

Baumuller BM5-O-SAF-002, Руководство по эксплуатации, Страница: 133 / 182

Поделиться
Скачать
Baumuller BM5-O-SAF-002 Скачать руководство пользователя страница 133

133

of 180

 Operation Manual 

Safety Module for b maXX 5000

 BM5-O-SAF-002/3

Document no.: 5.11016.03 

17

S

YSTEM

 

VALIDATION

All safety functions as well as the trouble-free functioning of the installed and 
parameterized system must be tested with the initial operation and after changes. The 
testing of the system must be documented.

WARNING!

Danger during commissioning!

The Safety Module may only be put into operation after being tested successfully by 
a technical expert. 

Therefore:

m

Conduct a complete function test. In doing so, check the correct allocation of the 
connected safety components.

m

A checklist for the commissioning and validation of the system is reproduced in 
Appendix 

Z

B.3 Commissioning and validation checklist

– 

from page 162 onward. 

Conduct the validation of the system in accordance with this checklist and 
document the procedure accordingly.

m

Make sure that operating personnel has been instructed in the handling of the 
Safety Module.

17.1 Function test

The function test is a major part of the validation of the entire system. The function test is 
used to determine the trouble-free allocation of the network safety components and the 
programmed logic of the system. 

Depending on the complexity of the logic circuit of the respective project, it is 
recommended to conduct the function tests in steps.

The following course of action is recommended when conducting the function tests:

1

Only connect the actuators and drives to the safe output terminals once no errors have 
been detected in the inspection of the logic circuit.

2

Conduct a complete function test with all sensors (initiators), switches, actuators and 
drives.

Содержание BM5-O-SAF-002























































































































































































Отзывы:

Нет отзывов