Baumuller BM5-O-SAF-002 Скачать руководство пользователя страница 119

Страница: 119 / 182

119

of 180

Operation Manual

Safety Module for b maXX 5000

BM5-O-SAF-002/3

Document no.: 5.11016.03

SSEMBLY

AND

INSTALLATION

This chapter describes the mechanical assembly and the electrical installation of the
Safety Module.

The assembly and installation process consists of the following steps:

Assemble the Safety Module.

Check the assembly and installation by means of the "Installation checklist" listed in
Appendix

B.2

–

on page 161.

15.1 General safety regulations

CAUTION!

The "Installation checklist" reproduced in Appendix

B.2

–

on page 161 must be used

during the assembly and installation phase.

Make sure that the installation process is carried out entirely in accordance with
the installation and wiring plan.

Conduct a visual inspection and check all system components for visible damage.

Check the system for wiring errors.

Check the tightening torque and make sure that the electrical connection is not
interrupted by insulation material.

Check the tensile-load capacity of the electrical terminal and screw connections.

Make sure that the installation and the cable routing are carried out in accordance
with applicable standards and guidelines.

Make sure that the system's environmental properties specified in Appendix

C.3.1

–

on page 166 are not exceeded.

Make sure that the design of the system's type of protection is sufficient.

Make sure that the safety system is not damaged by moving parts or work in the
area surrounding the installed safety components.

Make sure that the system components do not come into contact with aggressive
substances (such as acids, bases, transmission oil).

Follow the information in the chapter

Safety

–

from page 17 onward.

Содержание BM5-O-SAF-002























































































































































































Результаты поиска

Содержание BM5-O-SAF-002

Отзывы:

Baumuller BM5-O-SAF-002, Руководство по эксплуатации, Страница: 119 / 182

Результаты поиска

Содержание BM5-O-SAF-002

Отзывы: