manualshive.com logo in svg

Baumuller BM5-O-SAF-002, Руководство по эксплуатации, Страница: 108 / 182

Поделиться
Скачать
Baumuller BM5-O-SAF-002 Скачать руководство пользователя страница 108

NOTE!

Bit 0-4 in "S_StatusWord1" shows, at which safety function an error (such as a 
switchover to a parameter set, which was not defined) or a noncompliance (such as 
a limit violation) has occurred.

If several safety functions are triggered at the same time, the first safety function is 
displayed only, which is the one that initiated the error status. 

Starting from the module version "software extension" (with regard to the definition 
refer to 

Z

chapter 7.9

–

) an error code is transmitted in bit 5-7, describing the 

noncompliance more precisely. 

Status word "S_StatusWord2": Reading of digital inputs and outputs for a 
quicker diagnosis

Operation Manual 

Safety Module for b maXX 5000

 BM5-O-SAF-002/3

Document no.: 5.11016.03

Baumüller Nürnberg GmbH

108

of 180

12.7

12.7 Status word "S_StatusWord2": 

Reading of digital inputs and outputs for a quicker diagnosis

The statuses of the safe in- and outputs of the Safety Module can be read by a higher-
level safety control via FSoE.

All safe inputs at the SAF-module can be configured with ProSafePara for the activation 
of safe functions on axis 1 and on axis 2. 

However, if only one axis is configured in a single or double axis, there is no FSoE-
telegram generated for axis 2 and no FSoE-slave-response of axis two takes place. The 
evaluation of 

S_StatusWord2

 of axis 2 in the FSoE-master is omitted. 

Therefore, all relevant digital inputs were completely mapped into 

S_StatusWord2

 of 

axis 1.

The status word for axis 1 is structured as shown in the table below. For a quick diagnosis, 
in addition to the inputs, also the statuses of defined digital inputs and outputs at the SAF-
module are contained.

The terminal markings match with those in ProSafePara, the pin assignments refer to the 
terminal representation (see 

Z

Figure 45

– 

on page 90).

Coding of 

S_StatusWord2

 Axis 1 

Bit

 

Terminal marking

 

Pin A/B

 

Meaning

 

Bit 0

STO_IN_1

17/35

STO-Input group/axis 1

Bit 1

DIG1_IN_1

15/33

Input 1 group/axis 1

Bit 2

DIG2_IN_1

14/32

Input 2 group/axis 1

Bit 3

DIG3_IN_1

12/30

Input 3 group/axis 1

Bit 4

CHAIN_IN_1

16/34

Daisy Chain Input group/axis 1

Bit 5

DIG_OUT_1A

10

Output group/axis 1 A

Bit 6

DIG_OUT_1B

28

Output group/axis 1 B

Bit 7

Brake axis 1

-

Internal output axis 1 to the controller

Bit 8

CHAIN_OUT_1

13/31

Daisy Chain output axis 1

Bit 9

STO_IN_2

2/20

STO-input group/axis 2

Bit 10

DIG1_IN_2

4/22

Input 1 group/axis 2

Содержание BM5-O-SAF-002























































































































































































Отзывы:

Нет отзывов