manualshive.com logo in svg

Baumuller b maXX BMC-M-SAF-02, Руководство по эксплуатации

Поделиться
Скачать
Baumuller b maXX BMC-M-SAF-02 Скачать руководство пользователя страница 18

Intended use

Operation Manual 

b maXX safe PLC

 BMC-M-SAF-02

Document no.: 5.07020.04

Baumüller Nürnberg GmbH

18

of 118

4.3

4.3

Intended use

This device is exclusively designed and constructed for the intended purpose of use de-
scribed here.

The 

b maXX safe PLC

 uses for operation an attached power supply (BMC-M-PSB-02). 

Furthermore, the safety control can be expanded by the addition of various system com-
ponents.

Your use of the device is considered to be compliant with its intended use if you have read 
all instructions and information in this Operation Manual.

WARNING!

Danger due to use other than intended!

Any use of the device different from and/or exceeding beyond the scope of the intend-
ed use can lead to dangerous situations.

Therefore:

m

Only use the device as intended.

m

Follow all specifications of this Operation Manual.

m

Ensure that exclusively qualified personnel work on or with this device.

m

Take care in project planning to see that the device is always used within its spec-
ifications.

m

The device and/or mounting rail is mounted on a wall which is sufficiently sturdy.

m

Ensure that the power supply meets the required specifications.

m

Only operate the device if it is in technically faultless condition.

m

Only use the device in combination with components approved by Baumüller Nürn-
berg GmbH.

m

Only operate the device in type two environments. The device has been developed 
to meet the requirements of the category C3 according to IEC 61800-3:2005. The 
device is not intended to be connected to the public power grid. For operation of 
the device in a type one environment of the category C2/C1 (residential, business 
and commercial zone without an intermediate transformer directly to the low-volt-
age grid), special measures to reduce emitted interference (grid-bound and radiat-
ed) are to be arranged by a electrical cabinet engineer and must be demonstrated, 
since electromagnetic compatibility disturbances can occur unless additional mea-
sures are taken. It can not be guaranteed that a device described here will achieve 
category C2/C1 even with additional measures.

Содержание b maXX BMC-M-SAF-02

























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды