Baumer VisiLine Скачать руководство пользователя страница 61

Страница: 61 / 68

10.9 Message Channel

The asynchronous message channel is described in the GigE Vision

standard and of-

fers the possibility of event signaling. There is a timestamp (64 bits) for each announced

event, which contains the accurate time the event occurred. Each event can be activated

and deactivated separately.

10.9.1 Event Generation

Event

Description

Gen<i>Cam™

ExposureStart

Exposure started

ExposureEnd

Exposure ended

FrameStart

Acquisition of a frame started

FrameEnd

Acquisition of a frame ended

Line0Rising

Rising edge detected on IO-Line 0

Line0Falling

Falling edge detected on IO-Line 0

Line1Rising

Rising edge detected on IO-Line 1

Line1Falling

Falling edge detected on IO-Line 1

Line2Rising

Rising edge detected on IO-Line 2

Line2Falling

Falling edge detected on IO-Line 2

Line3Rising

Rising edge detected on IO-Line 3

Line3Falling

Falling edge detected on IO-Line 3

Vendor-specific

EventError

Error in event handling

EventLost

Occured event not analyzed

TriggerReady

notready

elapsed, camera is able to

process incoming trigger

TriggerOverlapped

Overlapped Mode detected

TriggerSkipped

Camera overtriggered

Содержание VisiLine





































































Результаты поиска

Содержание VisiLine

Отзывы:

Бренды по названию

Популярные бренды

Baumer VisiLine, Руководство пользователя

Результаты поиска

Содержание VisiLine

Отзывы:

Бренды по названию

Популярные бренды