manualshive.com logo in svg

Baumer O200, Инструкция по эксплуатации

Поделиться
Скачать
Baumer O200 Скачать руководство пользователя страница 21

 

en_BA_O200_IO-Link_V1.docx 

21/34 

Baumer Electric AG 

15.08.2018/ 

 

Frauenfeld, Switzerland

 

4.6 

Local User Interface 

Different parameters are available to configure the local user interface which means the indication LED and 
the qTeach availability or qTeach mode (Xpress vs Xpert, static vs dynamic) 
 

4.6.1 

Local Teach Settings 

Parameter name 

Short Description 

Rights 

Unit / Allowed values 

Teach Lock Settings.Teach Lock Time 
 
 
 
This parameter is only applicable for the 
qTeach – the teach-in by wire is not 
affected / locked at any time. 

Defines the time between 
power up and qTeach 
deactivation. 
 
0:  
qTeach never locked 
 
1 

– 120 min:  

Accepted range 
 
0xFF:  
qTeach always 
locked 
 
Default: 5 min 

rw 

0 

… 120 min 

0xFF 

Teach Mode Settings.Teach Mode 

Defines the teach mode for 
the qTeach and teach by 
wire. 

rw 

Xpert Static 
Xpress Static 
Xpert Dynamic 
Xpress Dynamic 

 
 

 

Содержание O200



































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды