Baumer MAGRES BMMS M75 Скачать руководство пользователя страница 14

Страница: 14 / 20

Manual_BMMS_CANopen_BECH_EN_rev05.docx

14/20

Baumer Electric AG

18.06.2013

Frauenfeld, Switzerland

8.2

Absolute encoder with cable-pull system

Figure 6: Block diagram encoder

Position Monitoring Encoder A Error

Battery Monitoring Error

Reset

Generic Position Alarm (Bit 0)

Position Alarm A (Bit 12)

Battery Warning (Bit 4)

Generic Error (Bit 4)

Communication Error (Bit 0)

CAN-Controller

Bus Passiv

Bus Off

Bus Warning

Bus Active

RX Buffer Overflow

Error Behaviour

1029h-2h

Error Behaviour

1029h-1h

8100h

8120h

8110h

5000h

Emergency Message

Write xxx0 xxxx xxxx xxxx to Alarms (6503h)

Alarms 6503h

Error Register 1001h

Warnings 6505h

Emergency Error Codes

Reset Reason Watchdog

Watchdog Warning (Bit 2)

6100h

8.3

Error behavior

The error behaviors are executed when the corresponding bit in object 1001 Error register is set and the device is in the
NMT-State Operational.

Example:
The error behavior 1029h-

2 is set to “Change to Pre-Operational” (0). The device is in NMT state Operational

1. Generic error bit is set.

→ The device changes to Pre-Operational

2. The device is forced to NMT state Operational with NMT command Start

→ The device changes again to Pre-Operational if the generic error bit is not cleared.

Содержание MAGRES BMMS M75





















Результаты поиска

Содержание MAGRES BMMS M75

Отзывы:

Похожие инструкции для MAGRES BMMS M75

Бренды по названию

Популярные бренды

Baumer MAGRES BMMS M75, Руководство пользователя

Результаты поиска

Содержание MAGRES BMMS M75

Отзывы:

Похожие инструкции для MAGRES BMMS M75

Бренды по названию

Популярные бренды